1)  mold-like bacteria
霉菌形细菌
2)  mould
霉菌
1.
Examination of Mould and Microzyme in Sugar;
食糖中霉菌及酵母菌的检测
2.
Study on the mould changes in Mu-Zi soy sauce mash;
母子酱油发酵酱醅中霉菌菌相的研究
3.
Preliminary Investigation on Mould in Book collection of the Library in University;
高校图书馆藏书霉菌孳生情况初步调查
3)  mold
霉菌
1.
Experimental research on mold resistance of paint film and gasket cement film:part 3 of the series of research practice of the national standard task group for the Code for cleanroom construction and acceptance test;
漆膜和密封胶膜耐霉菌的实验研究——国标《洁净室施工及验收规范》编制组研讨系列课题之三
2.
Comparisons of activities of chitin deacetylase from mold strains and study of its properties;
几种霉菌产甲壳素脱乙酰酶活力比较及部分酶学性质
3.
Study on fermented mash of rice wine on inhibition to mold;
黄酒发酵醪抑制霉菌生长的初步探讨
4)  fungus
霉菌
1.
Technical analysis and discussion on fungus test;
霉菌试验技术分析与探讨
2.
Formaldehyde-degrading ability of three strains of fungus;
3株霉菌对甲醛转化能力的研究
3.
For preventing fungus growth in electronic products,it is the most economical and effective method that covering mouldproof coatings or spraying protectants on the surfaces of the material and parts.
通过对1280件电子产品(或主要组成材料和工艺试片)霉菌试验结果的统计分析,总结出各种电子产品常用材料,特别是几种常用有机涂层的防霉特性。
5)  mildew
霉菌
1.
Analysis of Microstructures and Mechanical Properties of Protein Fibers Biodegraded by Mildew;
霉菌作用下蛋白质纤维的微观结构与力学性能
2.
The result showed that crude protein content in food residue could be increased by compound culture of microzyme and mildew,and crude protein content rose with reaction time increasing.
结果表明:酵母菌和霉菌联合作用于食物垃圾可以提高其粗蛋白含量,且粗蛋白含量随反应时间的延长而增加;康宁木霉3。
3.
The mildew's effects on military material in storage and transportation by container were analyzed detailedly.
针对军用物资集装箱储运过程中存在各种霉菌的实际情况,详细分析了其对箱体和箱内物资的影响,根据霉菌腐蚀机理和生长条件,较全面地总结了预防霉菌的各项措施。
6)  moulds
霉菌
1.
Study on moulds change current from aerobic composting of chicken manure;
禽粪便好氧堆肥过程中霉菌的变化趋势
2.
Characteristic of moulds decomposing from aerobic composting of chicken manure;
鸡粪好氧堆肥中霉菌的筛选及降解特性
3.
Review on Biosorption of Heavy Metal by Moulds;
霉菌吸附重金属离子的研究进展
参考词条
补充资料:J形及L形密封
分子式:
CAS号:

性质:两种均为唇形橡胶密封,截面形状分别为J形和L形。多为纯橡胶制品,也有少数是夹布制品。根据使用条件,一般用天然橡胶或丁腈橡胶制造。结构较简单,摩擦力低,专用于气压或液压机械设备的活塞及活塞杆密封,工作压力在1MPa以下,如用于汽车和火车制动系统及离合器操纵系统中,起传递压力和密封的作用。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。