1) diaphragm
薄膜活门
1.
According to the fracture and trace analysis of the failed diaphragm membrane,contrasting the bushes that were made by different factories,and ground compression test of the normal diaphragm membrane,it is found that,the accident that the airplane front-canopy dropped was caused by the abnormal break of membrane.
通过对抛舱盖薄膜活门膜片的断口和痕迹分析,对不同生产厂家的衬套R角加工质量进行对比以及用原机前舱盖薄膜活门进行地面耐压试验等分析验证工作,确定飞机发生飞掉前座舱盖的事故征候是由于抛盖薄膜活门的膜片异常爆破造成。
2) emergency diaphragm valve
应急薄膜活门
3) thin film
薄膜
1.
Effects of annealing temperature on microstructure and cohesion of ZrW_2O_8 thin films;
退火温度对ZrW_2O_8薄膜结构和结合力的影响
2.
Fabrication and low temperature sintering of GDC thin film;
氧化钆掺杂纳米氧化铈薄膜的制备与烧结性能研究
3.
Fabrication of CuS nano/micro tube thin films and CuO nano/micro crystal thin films using CuCl nanorod films as precursor;
以CuCl纳米棒薄膜为前驱体制备CuS纳米/微米管和CuO纳米/微米晶薄膜
4) membrane
薄膜
1.
Air filtration performance of nanofibrous membranes electrospuned with different nanofiber diameters;
电纺不同直径纳米纤维薄膜的空气过滤性能
2.
Solving the Problem of Break in Deep-drawing Work by using Plastic Membrane;
用塑料薄膜解决深拉深件的拉深破裂问题
3.
Texture feather analysis of the membrane wrinkling;
薄膜褶皱的纹理特征分析
5) film
薄膜
1.
Photocatalytic Degradation of Toluene in Gas-phase Using C-TiO_2 Nano-film;
含碳纳米C-TiO_2薄膜光催化降解气相甲苯研究
2.
Al-doped ZnO thin films prepared through ion implantation;
金属铝离子注入掺杂制备氧化锌铝薄膜的研究
3.
Structure and corrosion resistance of self-assembled sulf-silane film on surface of Mg-Gd-Y-Zr alloy;
Mg-Gd-Y-Zr合金表面含硫硅烷薄膜的结构与耐蚀性能
6) films
薄膜
1.
Effect of plasticizer on property of films of polymer-polyvinyl alcohol;
复配增塑剂对聚乙烯醇薄膜性能的影响
2.
Fabrication and forming mechanism of alumina nanowire films by anodizing method;
阳极氧化法制备氧化铝纳米线薄膜及其生成机理研究
3.
Thickness-dependent transport properties of La2/3Sri/3MnO3 polycrystalline films;
不同厚度的La_(2/3)Sr_(1/3)MnO_3多晶薄膜输运性质研究
参考词条
补充资料：活门
分子式：
分子量：
CAS号：
性质：见阀。
分子量：
CAS号：
性质：见阀。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。