1) Titanium and its' alloy
钛及合金
2) titanium and its alloys
钛及钛合金
1.
A simultaneous determination of oxygen and hydrogen in titanium and its alloys on infrared absorption has been described,and the optimal conditions have been obtained.
叙述了用红外吸收法对钛及钛合金中氧和氢联合测定的方法,取得了测定的最佳条件。
2.
Anodizing coloring mechanism of titanium and its alloys was analyzed to make sure the relationship of fiun thickness and coloring power source, so that the technological method and current design parameters were deduced to keep the color consistence of bath production, which provided an available method for coloring of titanium and its alloys.
分析了钛及钛合金阳极氧化着色机理及色膜厚度与氧化着色电源之间的关系,得出了保证成批量着色颜色一致性的工艺方法及电流设计参数,为钛及钛合金着色的应用提供了一种可用的方法。
3.
However, the production and utilization of titanium and its alloys are limited for their high chemical activity at molten state.
钛及钛合金具有密度小、强度高、耐腐蚀等一系列优点,在航空航天、国防军事、民用轻工等领域均有广泛应用前景。
3) Ti and its alloy
钛及钛合金
1.
The determination of Zr, Ru, Pd, Hf, Cu, Y, V, Mo, Nb, Al, Co, Ni, Ta, Bi, Sn, Cr and Mn in Ti and its alloys have been studied using an atomic emisson spectrum spectroscopy.
采用发射光谱分析技术,研究了钛及钛合金中Zr,Ru,Pd,Hf,Cu,Y,V,Mo,Nb,Al,Co,Ni,Ta,Bi,Sn,Cr,Mn的光谱测定方法。
4) titanium and titanium alloy
钛及钛合金
1.
Discussion about specified residual elongation stress in the standard of titanium and titanium alloy;
钛及钛合金标准中规定残余伸长应力的探讨
2.
Preparation of metallographic specimen for titanium and titanium alloy used for surgical implants
外科植入物用钛及钛合金金相试样制作浅谈
3.
The paper introduces the possibility of application of the titanium and titanium alloy for wrought products of motorcar.
介绍了汽车中使用钛及钛合金各类加工材的可能性。
5) titanium and its alloy
钛及钛合金
1.
As the markets of aerospace for the thick titanium and its alloy plate are more and more of the increase,it is impossible to meet the requirements of aerospace industry for the traditional blaze incision,so the experiments of waterjet process for cutting thick titanium and its alloy plate were performed.
随着世界航空市场趋好,钛及钛合金中厚板的需求旺盛,采用传统的火焰切割方式切割钛及钛合金已无法满足航空工业的需求。
2.
The utilization factor of materials for powder metallurgy parts can reach 100%,it is the important way to reduce the production cost of titanium and its alloy parts.
钛及钛合金具有优良的综合力学性能,在航空航天、航海、化工等领域得到日益广泛的应用。
3.
To meet the demands of welding titanium and its alloy electrode in large size.
为了满足大尺寸钛及钛合金电极的焊接要求,宝钛集团有限公司依据等离子弧的压缩效应原理及电弧的稳定性原理,对从德国引进的钛及钛合金真空等离子焊箱枪体的阴极和喷嘴进行了技术改造。
6) Ti and Ti alloy
钛及钛合金
1.
The microstructure, properties and impact fracture toughness of welded joints of Ti and Ti alloy by using tungsten-argon arc welding were studied.
研究了钛及钛合金经钨极氩弧焊焊接接头的显微组织、力学性能和冲击断裂特征。
2.
Ti and Ti alloy were applied widely in airline and aerospace industry because of its excellent performance.
钛及钛合金由于其优良的性能被广泛应用于航空、航天等重要工业部门，同时钛对绝热剪切敏感，在高应变速率形变条件下易产生所谓的绝热剪切带，而关于绝热剪切带内的微观组织演化规律是人们研究的焦点。
补充资料：电解法生产铝钛母合金
电解法生产铝钛母合金
production of aluminium-titanium master alloy by electrolysis
d lonJ一efo shengehan}口to}muhejln电解法生产铝钦母合金(product，()n of azu-minium一titanium master alloy by eleetrolysis) 在_〔业铝电解中，向电解槽加入钦的化合物在阴极产出铝钦母合金的过程。为熔盐电解法生产铝墓母合金方法之一。所用的钦化合物主要是钦的氧化物 铝钦母合金通常是在电弧炉或感应炉内由纯金属钦和铝熔合而成。这种生产铝钦母合金的方法不但多耗了重熔时的电能，而且使用了昂贵的金属钦。而用电解法生产铝钦母合金时，只要把价格便宜的金红石(Tio:)加到电解槽中，即可直接得到铝钦母合金。 研究发现，当把TIO:加到电解槽中后，铝电解质中的Tio:既会被铝还原成金属: 3一一3_、. ZAI+言TIOZ一言T‘十AIZ()3也会在阴极上发生电化学还原反应生成金属: Ti4十十4c一Ti如果电解过程为一次性加料，则电解前期以铝热还原反应为主，后期以电化学还原反应为主。 在电解法生产铝钦母合金中，TIO:每次向电解槽中添加量不得过多，否则会发生T心:沉淀，因为Ti。，在冰晶石中的溶解度远小于A1203在冰晶石中的溶解度。电解法生产的铝钦母合金一般以含钦2%一3写为宜。 (张明杰徐树田)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条