1) TG6 Titanium Alloy
TG6钛合金
1.
Analysis of the Uncertainty for the Determination of Trace Nickel in TG6 Titanium Alloy by AAS;
原子吸收光谱法测定TG6钛合金中痕量镍不确定度的分析
2.
The influences of the amount of HCl(1+1) and HBF_4(1+4),and titamium and coexisting elements on the determination of Ni in TG6 titanium alloy have been investigated.
采用原子吸收光谱测定TG6钛合金中痕量镍。
2) titanium and its alloys
钛和钛合金
1.
The barriers were prospected to be used in titanium and its alloys as protective coatings.
概述了防止氢和氢同位素渗透壁垒层的研究进展,展望了这些壁垒层在钛和钛合金基体上的应用前景。
3) titanium and its alloys
钛及钛合金
1.
A simultaneous determination of oxygen and hydrogen in titanium and its alloys on infrared absorption has been described,and the optimal conditions have been obtained.
叙述了用红外吸收法对钛及钛合金中氧和氢联合测定的方法,取得了测定的最佳条件。
2.
Anodizing coloring mechanism of titanium and its alloys was analyzed to make sure the relationship of fiun thickness and coloring power source, so that the technological method and current design parameters were deduced to keep the color consistence of bath production, which provided an available method for coloring of titanium and its alloys.
分析了钛及钛合金阳极氧化着色机理及色膜厚度与氧化着色电源之间的关系,得出了保证成批量着色颜色一致性的工艺方法及电流设计参数,为钛及钛合金着色的应用提供了一种可用的方法。
3.
However, the production and utilization of titanium and its alloys are limited for their high chemical activity at molten state.
钛及钛合金具有密度小、强度高、耐腐蚀等一系列优点,在航空航天、国防军事、民用轻工等领域均有广泛应用前景。
4) Ti and its alloy
钛及钛合金
1.
The determination of Zr, Ru, Pd, Hf, Cu, Y, V, Mo, Nb, Al, Co, Ni, Ta, Bi, Sn, Cr and Mn in Ti and its alloys have been studied using an atomic emisson spectrum spectroscopy.
采用发射光谱分析技术,研究了钛及钛合金中Zr,Ru,Pd,Hf,Cu,Y,V,Mo,Nb,Al,Co,Ni,Ta,Bi,Sn,Cr,Mn的光谱测定方法。
5) titanium and titanium alloy
钛及钛合金
1.
Discussion about specified residual elongation stress in the standard of titanium and titanium alloy;
钛及钛合金标准中规定残余伸长应力的探讨
2.
Preparation of metallographic specimen for titanium and titanium alloy used for surgical implants
外科植入物用钛及钛合金金相试样制作浅谈
3.
The paper introduces the possibility of application of the titanium and titanium alloy for wrought products of motorcar.
介绍了汽车中使用钛及钛合金各类加工材的可能性。
6) titanium and its alloy
钛及钛合金
1.
As the markets of aerospace for the thick titanium and its alloy plate are more and more of the increase,it is impossible to meet the requirements of aerospace industry for the traditional blaze incision,so the experiments of waterjet process for cutting thick titanium and its alloy plate were performed.
随着世界航空市场趋好,钛及钛合金中厚板的需求旺盛,采用传统的火焰切割方式切割钛及钛合金已无法满足航空工业的需求。
2.
The utilization factor of materials for powder metallurgy parts can reach 100%,it is the important way to reduce the production cost of titanium and its alloy parts.
钛及钛合金具有优良的综合力学性能,在航空航天、航海、化工等领域得到日益广泛的应用。
3.
To meet the demands of welding titanium and its alloy electrode in large size.
为了满足大尺寸钛及钛合金电极的焊接要求,宝钛集团有限公司依据等离子弧的压缩效应原理及电弧的稳定性原理,对从德国引进的钛及钛合金真空等离子焊箱枪体的阴极和喷嘴进行了技术改造。
补充资料：低温钛合金
分子式：
CAS号：
性质：适合低温下使用的α和α-β钛合金。可分为三类：α,β及α-β钛合金。在很宽的低温范围使用的钛合金主要有：工业钝钛，Ti-5Al-2.5Snα合金，Ti-6Al-4V和Ti-8Al-1Mo-1V α-β合金。为改善低温塑性与韧性，又分出一类间隙元素特别低的ELI低温钛合金(超低间隙元素钛等)。典型的合金有Ti-5Al-2.5SnELI和Ti-6Al-4V ELI。Ti-5Al-2.5Sn ELI合金特别适合用于在-253℃的低温下工作的液体燃料储存容器，Ti-6Al-4V ELI亦具有较好的低温塑性和更高的断裂韧性，适合于制造一般低温容器和要求高断裂韧性的飞机结构锻件及厚板结构。
CAS号：
性质：适合低温下使用的α和α-β钛合金。可分为三类：α,β及α-β钛合金。在很宽的低温范围使用的钛合金主要有：工业钝钛，Ti-5Al-2.5Snα合金，Ti-6Al-4V和Ti-8Al-1Mo-1V α-β合金。为改善低温塑性与韧性，又分出一类间隙元素特别低的ELI低温钛合金(超低间隙元素钛等)。典型的合金有Ti-5Al-2.5SnELI和Ti-6Al-4V ELI。Ti-5Al-2.5Sn ELI合金特别适合用于在-253℃的低温下工作的液体燃料储存容器，Ti-6Al-4V ELI亦具有较好的低温塑性和更高的断裂韧性，适合于制造一般低温容器和要求高断裂韧性的飞机结构锻件及厚板结构。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条