1) titanium alloy
钛合金
1.
Finite element analysis of adiabatic shear band formation in titanium alloy cutting process;
钛合金切削绝热剪切带形成过程的有限元分析
2.
Reactive electric-spark deposition Ti(C N)-based ceramets coating on titanium alloy;
钛合金表面反应电火花沉积Ti(CN)涂层研究
3.
Numerical simulation of vacuum hot bulge forming of titanium alloy cylindrical workpiece;
钛合金筒形件真空热胀形过程数值模拟
2) Ti alloy
钛合金
1.
The finite element analysis and experiment research of Ti alloy rod on continuous rolling with flat triangle-round passes;
平三角-圆孔型连轧钛合金棒材的有限元分析与试验研究
2.
Quantitative relationship between impact property and dynamic compressive performance of Ti alloy;
钛合金冲击性能与动态压缩性能间的定量关系
3.
Surface characteristic of coatings of biomedical Ti alloy by micro-arc oxidation;
生物医学钛合金微弧氧化涂层的表面特征
3) titanium and its alloys
钛和钛合金
1.
The barriers were prospected to be used in titanium and its alloys as protective coatings.
概述了防止氢和氢同位素渗透壁垒层的研究进展,展望了这些壁垒层在钛和钛合金基体上的应用前景。
4) titanium and its alloys
钛及钛合金
1.
A simultaneous determination of oxygen and hydrogen in titanium and its alloys on infrared absorption has been described,and the optimal conditions have been obtained.
叙述了用红外吸收法对钛及钛合金中氧和氢联合测定的方法,取得了测定的最佳条件。
2.
Anodizing coloring mechanism of titanium and its alloys was analyzed to make sure the relationship of fiun thickness and coloring power source, so that the technological method and current design parameters were deduced to keep the color consistence of bath production, which provided an available method for coloring of titanium and its alloys.
分析了钛及钛合金阳极氧化着色机理及色膜厚度与氧化着色电源之间的关系,得出了保证成批量着色颜色一致性的工艺方法及电流设计参数,为钛及钛合金着色的应用提供了一种可用的方法。
3.
However, the production and utilization of titanium and its alloys are limited for their high chemical activity at molten state.
钛及钛合金具有密度小、强度高、耐腐蚀等一系列优点,在航空航天、国防军事、民用轻工等领域均有广泛应用前景。
5) Ti and its alloy
钛及钛合金
1.
The determination of Zr, Ru, Pd, Hf, Cu, Y, V, Mo, Nb, Al, Co, Ni, Ta, Bi, Sn, Cr and Mn in Ti and its alloys have been studied using an atomic emisson spectrum spectroscopy.
采用发射光谱分析技术,研究了钛及钛合金中Zr,Ru,Pd,Hf,Cu,Y,V,Mo,Nb,Al,Co,Ni,Ta,Bi,Sn,Cr,Mn的光谱测定方法。
6) titanium and titanium alloy
钛及钛合金
1.
Discussion about specified residual elongation stress in the standard of titanium and titanium alloy;
钛及钛合金标准中规定残余伸长应力的探讨
2.
Preparation of metallographic specimen for titanium and titanium alloy used for surgical implants
外科植入物用钛及钛合金金相试样制作浅谈
3.
The paper introduces the possibility of application of the titanium and titanium alloy for wrought products of motorcar.
介绍了汽车中使用钛及钛合金各类加工材的可能性。
补充资料：钛合金
| 钛合金 titanium alloy 以钛为基体加入其他合金元素而构成的有色合金。其主要添加元素有铝、锡、锰、钒、铬、钼、铁、硅、铜等。在退火状态下，钛合金的相组成分为a型、β型和（a＋β )型3类，中国分别以TA、TB和TC表示。与其他金属材料相比 ，钛合金比强度高，中温、低温性能好；在氧化性介质中，合金表面能生成一层牢固而致密的、破坏后又能自愈的氧化膜，可防止金属进一步氧化，故钛合金又具有较好的耐腐蚀性。 钛合金按用途分为：①耐蚀钛合金。除具有一般钛合金的耐蚀性能外，还具有高断裂韧性和高强度、低的应力腐蚀敏感性和耐海水和化工介质的腐蚀性能。主要用于制造潜艇壳体和海洋压力容器等。②耐热钛合金。通过固溶强化、弥散强化等工艺获得较好的高温性能，使用温度在400℃以上。用于制造飞行器蒙皮、航天工业用发动机零件等。③高强度钛合金。强度可达1200～2000兆帕（MPa）。主要用于制造飞机构件，还可制造耐蚀设备、运动器具等。④低温钛合金。可在液氧、液氢温度下使用，具有高的低温塑性和韧性。用于制造液态气体的容器和需要高塑性、高韧性的零件。⑤粉末钛合金。用粉末冶金方法制成，可代替变形钛合金制造各种半精密形状的零件，能提高材料的利用率，降低制造成本。⑥功能钛合金。主要有镍钛形状记忆合金、铁钛储氢材料等。 |
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条