1) chopped high modulus carbon fiber
短切高模炭纤维
1.
The effects of graphitization degree and fiber content on the properties of C/C composites reinforced with chopped high modulus carbon fiber were studied by XRD and SEM.
以短切高模炭纤维为增强体。
2) short-cutting
短切
3) chopped strand mat
短切毡
1.
To prepare a fast wet-out,internally plasticizing binder for flexible E-glass fiber chopped strand mat,researches were made on both formulation and synthesizing technology.
从配方和工艺两方面着手,为制备出渗透快、内增塑的柔软性优良的无碱玻璃纤维短切毡粘结剂,研究了粘结剂配方中丙烯酸用量、自制内增塑单体配比、单体的加料顺序等对粘结剂性能的影响,而且考察了引发剂用量与反应温度的关系。
2.
This article introduces the equipment and technology for producing glass fiber chopped strand mat(CSM)by describing the key process parameters and main equipment units in the whole process, including the mat-forming section, binder section, oven section, wind-up section and line speed regulation.
叙述了短切毡生产流程中的成形段,粘结剂段,烘干段,卷取段以及生产线速度的调节所涉及到的主要工艺技术参数和主要设备及其工作原理。
3.
With ammonium persulfate/sodium thiosulfate as Redox initiator system,a binder based on vinyl acetate/acrylate copolymer used for chopped strand mat was prepared at low temperature.
以过硫酸铵/硫代硫酸钠为氧化还原引发体系,在低温下研究制备出了短切毡用的醋酸乙烯酯与丙烯酸酯类共聚物粘结剂。
4) short fiber
短切纤维
1.
Results showed that the friction coefficients of short fiber C/SiC and 3D needleded C/SiC brake disks were 0.
采用反应熔体渗透工艺制备了短切纤维C/S iC与三维针刺C/S iC复合材料,在MM-1000型摩擦磨损试验机上考察了2种结构C/S iC复合材料在模拟飞机正常着陆时的摩擦磨损性能。
2.
From lengthways tensile strength of unilateral uninterrupted fiber reinforced composite, and analyzing the rneso-rnechanics and deformation,a strength predicting formula of short fiber reinforced composite has been established by using the dimensions of short fiber to amend the influence of its length and orientation on tensile strength.
在分析单向连续纤维增强复合材料纵向拉伸时细观受力与变形的基础上,对连续纤维的长度和方向进行尺寸和方向性修正,给出了短切纤维增强复合材料的拉伸强度预测公式。
5) short glass fibre
短切玻纤
1.
In this paper, the effect of silicane coupling agent γ-aminopropyl triethy-oxysilane(A-1100) on interface properties of short glass fibre reinforced polycarbonate is report-ed.
针对短切玻纤增强聚碳酸酯体系,研究了硅烷偶联剂γ-氨丙基三乙基硅烷(A-1100)在上述复合体系中的界面偶联特性。
6) Short cutting edge
短切口
参考词条
补充资料：切膜纤维
分子式：
CAS号：
性质：又名扁丝，亦称割裂纤维。指由将成纤高聚物制成薄膜后，使之通过一定隔距的刀架，切割成宽约2.5～6mm，厚约20～50μm单轴拉伸的扁条均属之。该方法主要用于生产聚丙烯的扁丝。产品力学性能：强度3.14～4.42cN/dtex，伸长率10%～30%。扁丝的相对密度0.90，可用于制作工业用包扎绳、编织包装袋、地毯的衬底织物等。
CAS号：
性质：又名扁丝，亦称割裂纤维。指由将成纤高聚物制成薄膜后，使之通过一定隔距的刀架，切割成宽约2.5～6mm，厚约20～50μm单轴拉伸的扁条均属之。该方法主要用于生产聚丙烯的扁丝。产品力学性能：强度3.14～4.42cN/dtex，伸长率10%～30%。扁丝的相对密度0.90，可用于制作工业用包扎绳、编织包装袋、地毯的衬底织物等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。