1) Short carbon fiber
短切炭纤维
1.
Short carbon fiber reinforced pitch-based carbon/carbon composites (SCFRC) with high density and low cost were fabricated by mold pressing followed by semi-carbonization.
利用模压半炭化成型工艺在大气环境下制备出了短切炭纤维增强沥青基C/C复合材料(简称SCFRC)。
2.
Short carbon fiber reinforced pitch-based carbon/carbon composites (SCFRC) with high density and low cost were fabricated under atmospheric conditions by a new and efficient mould pressing and semi-carbonization shaping technology.
利用新型、高效的模压半炭化成型工艺,在大气环境下制备出了短切炭纤维增强沥青基C/C复合材料制品,并借助光学显微镜和扫描电镜对其微观组织和断口形貌进行了观察。
2) Chopped carbon fiber
短切炭纤维
1.
The results show that chopped carbon fibers can efficiently enhance energy load permitting value and friction coefficient.
研究结果表明:添加短切炭纤维增强的材料能有效提高材料的能量许用负荷和摩擦因数;摩擦副的制动速度为1 500 r/min和2 500 r/min时,摩擦因数随制动压力的增加而减小;摩擦副的制动速度为3 500 r/min时,摩擦因数随制动压力的增大呈现先降低而后增大的趋势;当制动压力为1。
3) short carbon fiber
短炭纤维
1.
Friction and wear properties of short carbon fiber reinforced C/C-SiC braking materials;
短炭纤维增强C/C-SiC制动材料的摩擦磨损性能
2.
The short carbon fiber reinforced copper graphite composites was fabricated with powder metallurgy technology.
以高性能受电弓滑板为应用前景 ,研究了短炭纤维对铜 -石墨复合材料冲击性能的影响 。
3.
The short carbon fiber(Cf)reinforced phenolic resin(PF)/graphite(Gr)composites were fabricated by hot compression molding.
以短炭纤维(Cf)为增强相,超细石墨(Gr)为填充组分,热固性酚醛树脂(PF)为基体,采用热模压法制备Cf-PF/Gr复合材料。
4) short fiber
短切纤维
1.
Results showed that the friction coefficients of short fiber C/SiC and 3D needleded C/SiC brake disks were 0.
采用反应熔体渗透工艺制备了短切纤维C/S iC与三维针刺C/S iC复合材料,在MM-1000型摩擦磨损试验机上考察了2种结构C/S iC复合材料在模拟飞机正常着陆时的摩擦磨损性能。
2.
From lengthways tensile strength of unilateral uninterrupted fiber reinforced composite, and analyzing the rneso-rnechanics and deformation,a strength predicting formula of short fiber reinforced composite has been established by using the dimensions of short fiber to amend the influence of its length and orientation on tensile strength.
在分析单向连续纤维增强复合材料纵向拉伸时细观受力与变形的基础上,对连续纤维的长度和方向进行尺寸和方向性修正,给出了短切纤维增强复合材料的拉伸强度预测公式。
5) cut fibres
短纤维;切断纤维
6) short carbon fiber
短切碳纤维
1.
Experimental study on compressive strength of short carbon fiber concrete
短切碳纤维钢筋混凝土板的平截面试验研究
2.
Preparation and property of short carbon fiber reinforced HA/PMMA bio-composites
短切碳纤维增强HA/PMMA生物复合材料的制备及性能
3.
Electromagnetic parameters of the ferrites and short carbon fiber composites were measured,and reflectivity of single-layer and double-layer composites with the thickness of 2mm is calculated in Ku waveband respectively.
使用溶胶凝胶法制备了M型和W型六角铁氧体,测量了铁氧体、短切碳纤维复合材料在Ku波段的电磁参数,并计算了层厚为2mm的单层和双层复合材料反射率。
补充资料：短切纤维
分子式：
CAS号：
性质：长度为1～15mm的切断纤维。纤维长度由制成品性能决定。增加纤维长度，可提高制品强度，缩短纤维长度，可提高制品的各向同性。一般用丝束切断法加工。通过调节切断机刀距可以改变短切纤维长度。主要用于加工纤维增强复合材料、增强水泥制品和合成纸。
CAS号：
性质：长度为1～15mm的切断纤维。纤维长度由制成品性能决定。增加纤维长度，可提高制品强度，缩短纤维长度，可提高制品的各向同性。一般用丝束切断法加工。通过调节切断机刀距可以改变短切纤维长度。主要用于加工纤维增强复合材料、增强水泥制品和合成纸。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条