1) flatting
平整[法]
2) temper rolling
平整
1.
Cross breaks are formed on the surface of cold rolled and tempered strip during temper rolling,which influence the surface quality and mechanical characteristics of the temper rolled strip.
冷轧退火后的带钢在平整过程中产生横折印缺陷,严重影响平整后带钢的表面质量及其力学性能。
2.
The effect of over ageing (OA) and temper rolling on the mechanical properties of cold rolled low carbon SiMn dual phase steel sheets has been studied.
以低碳Si Mn系冷轧双相钢为研究对象,探讨了过时效和平整工艺对双相钢板力学性能的影响。
3) leveling
平整
1.
Aimed at the waves of thin gauge products and the limitation of leveling strip head or tail in temper mill,the function of leveling strip head has been developed and applied in production in Zhujiang Steel.
针对薄规格产品的浪形情况和平整机平整带钢头尾浪形所存在的缺陷等问题,珠钢自主开发了平整机带头平整程序,实现了平整机带头的平整功能,改善了产品的质量,提高了经济效益。
2.
This paper introduced the development state of the heat pressing plasticization leveling process technology of plant board surface and equipment all the world , and entered technology guideline of heat pressing plasticization technology of plant board surface in our country.
介绍了国内外生物质板材表面热压塑化平整加工技术和装备的发展现状,提出了我国研发热压塑化平整加工工艺和装备的技术路线。
4) skin rolling
平整
1.
During skin rolling,the plastic deformation of strip is small,so the error of prediction with equal deformation in the high direction is large.
根据轧件平整轧制时塑性变形量很小,变形沿带材高度不均匀分布的特点,采用沿高度应力均匀分布的平面假设将带来比较大的误差。
2.
The calculation method based on BP network for rolling force of skin rolling is introduced.
运用 BP网络建立了平整轧制压力计算方法 ,实际应用结果表明 :BP网络建立了平整轧制压力计算方法比较简单 ,计算精度高 ,计算误差小于 8% ,完全可以应用于工程实
3.
During skin rolling of comparatively thick strip,plastic deformation quantity is very small.
较厚带材平整轧制时塑性变形量很小 ,因此沿带材高度变形是不均匀分布的 ,而一般公式采用沿高度应力均匀分布的平面假设将带来比较大的误差。
5) Temper
平整
1.
Research into Effect of Temper on Properties of 08Al Cold Rolled Strip;
平整对08Al钢冷轧薄板性能影响的研究
2.
Study on the strip surface wrinkles and the elimination measures in cold temper rolling;
冷轧平整横折印缺陷产生原因和消除方法
3.
Experiment study on comprehensive evaluation of lubricant used in temper mill;
平整液综合评价实验研究
6) skin pass
平整
1.
Elastoplastic model with boundary lubrication of rolling press analysis for skin pass;
平整轧制压力预测的边界润滑弹塑性模型
2.
The theoretical and experimental study of the influence on micro convex profile duplication during skin pass has been done.
对平整轧制中轧辊表面微凸体形貌的复映率影响因素进行了理论分析和实验研究。
3.
Aimed at specially characteristics of skin pass and the consist proportion of lubricant, the study of predicting skin pass rolling force was carried out by theoretical analysis and experimental investigations with rigid, elastoplastic, complete sliding and boundary lubrication model.
针对平整工艺和平整液组成的特点,采用刚性、弹塑性、全滑动和边界润滑等不同模型,进行了平整轧制压力预测模型的理论分析与模拟实验研究。
7) pinch passing
平整
8) pinch rolling
平整
9) level up
平整
10) skin pass mill
平整机
1.
Elongation assignment of steel plates between a tension leveler and a skin pass mill for the Acid-Refined 2030 in BaoSteel;
宝钢2030酸洗机组中拉矫机和平整机的延伸率分配
2.
Improvement of tension control system of skin pass mill;
平整机张力控制系统的改进
3.
Speed control system of skin pass mill in Cold Strip Rolling Mill of Wuhan Iron &Steel Group Company;
武钢冷轧厂平整机速度控制系统
补充资料：平整
平整
temper
阶消失，同时使平整时产生的加工硬化减小，使板带材的加工性能得到改善。在平整中，通常以延伸率(哟代替冷轧时采用的压下率(:)，如忽略宽展，其间的关系式为 曰 7~了二飞 (于长生)P ingzheng平整(t emPer)对冷轧后并经过退火的板带材进行的小压下率的冷轧。一般不向板带材和轧棍喷射润滑油和冷却水，压下率为0.5%一4%。为了提高防锈性和改善表面质量，平整冷轧板带钢时，多采用水溶性和油溶性的防锈剂作为平整液，压下率可达10%。平整可提高板带材板形的平直度，改变表面粗糙度，消除或缩小退火板带材明显的屈服台阶、防止供冲压时表面出滑移线(见滑移)和断裂。早期的带卷平整机为单机架，为了提高硬度、改善表面粗糙度和生产超薄的镀锡板，出现双机架平整。平整机的轧辊尺寸、附属设备、轧制速度同冷轧机相似。平整压下率很小，一般多采用单辊传动，避免由于辊径差造成速度和扭矩的差异，降低平整质量和造成设备事故。深冲钢平整时的变形率一般采用。.6%一1.4%，用于包装的薄板带一般平整率约为l%~3%。有时还进行强化变形，其目的除了抑制滑移线倾向，以使轧件不断裂外，还要使板带达到一定的硬度。在平整薄板带和极薄板带时，常将平整变形分配在两个道次上，变形不均匀性将增大。在不均匀变形时，随着平均平整率的减小，可使屈服台
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条