1) eutectic temperature
共融温度
2) fusion temperature
熔融温度
1.
An in-depth study was conducted concerning the fusion temperature and fusion process dynamic characteristics of three representative pairs of ash samples taken from two units of coal water slurry (CWS)-fired boilers.
对取自2台水煤浆锅炉3对各具代表性灰的熔融温度和熔融过程动态特性进行了深入研究。
2.
Plenty of medical glass bottles which were present in medical wastes had rather low fusion temperatures.
实验结果显示,不同化学组分对熔融温度有不同的影响,SiO2能够提高医用玻璃的熔融温度,B2O3和碱金属氧化物(Na2O、K2O)会大幅降低医用玻璃的熔融温度,而碱土金属氧化物(CaO、BaO)和Al2O3会使医用玻璃的软化温度升高,却能使流动温度降低。
3) melting temperature
熔融温度
1.
The melting characteristics and behavior of heavy metals of fly ashes were investigated under different melting temperatures.
对城市垃圾与煤混烧飞灰进行旋风熔融试验,分析了不同熔融温度条件下熔渣的微观形貌及重金属行为。
2.
The influence of fly ash on partition characteristics of heavy metals before and after melting treatment was studied , including the melting temperature, melting time and the basicity.
研究探讨了熔融温度、熔融时间、碱基度对飞灰熔融处理前后重金属分布特性的影响。
3.
The melting temperature,melting heat,static and dynamic mechanical properties of PA6/PTFE blends and PA66/PTFE blends are experimentally investigated in this paper.
PA6/PTFE共混物的熔融温度随PTFE含量的增加而升高,熔融热却随PTFE含量的增加而降低。
4) melting point
熔融温度
1.
As irradiation dose increases, the gel content and charpy impact strength increases, whereas crystallinity, melting point and elongation at break decreases.
结果表明 :在 0～ 30 0 k Gy的辐射剂量范围内 ,限定量的氧对 HDPE的性能并无太大的影响 ,HDPE的凝胶含量和缺口冲击强度随辐射剂量的增加而增加 ,但结晶度、熔融温度和断裂伸长率却随剂量的增加而下降。
2.
By co polymerization between a flexible co-monomer and acrylonitrile reduces the melting point or increases the decomposition temperature in order to produce melt processable resin.
8℃,而熔融温度仅为188。
5) blend temperature
共混温度
1.
The composites of woodfiber and LLDPE/PS alloy in different blend ratios and blend temperatures were prepared and the appearance quality and the mechanical and physical properties of the composites were evaluated also.
结果表明:不同共混比例与共混温度对制备的塑料合金熔体流动性、力学强度有较显著影响。
6) eutectic temperature
共晶温度
1.
Experimental study on the eutectic temperature between NiZr and NiZr_2 compounds;
NiZr和NiZr_2共晶温度的测定
2.
Experiences in-core indicate that the swelling of metallic fuels is so severe that the cladding begins to fail at a low burnup,moreover the solidus temperature of uranium or uranium-plutonium fuel and eutectic temperature with stainless steel cladding materials are low and made it impractical to use metallic fuels in a commercial reactor.
国外早期快堆发展的燃料集中在金属燃料上,但金属燃料辐照肿胀严重,只能实现较低的燃耗深度,且较低的固相线温度和与包壳间的共晶温度又制约了金属燃料的实际应用。
补充资料：熔融温度
分子式：
CAS号：
性质：是物质的晶态和液态平衡共存的温度。有时也称熔点。晶体的熔点与所受压强有关。例如，每增加0.1MPa，冰的熔点约下降0.000745℃。在一定压强下，晶体的熔点和其凝固点相同。对于非晶态（如玻璃）来说，就没有熔点可言，只有软化温度范围。
CAS号：
性质：是物质的晶态和液态平衡共存的温度。有时也称熔点。晶体的熔点与所受压强有关。例如，每增加0.1MPa，冰的熔点约下降0.000745℃。在一定压强下，晶体的熔点和其凝固点相同。对于非晶态（如玻璃）来说，就没有熔点可言，只有软化温度范围。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条