1) ash fusion temperature
灰熔融温度
1.
The mechanism of reducting of ash fusion temperature by adding flux in Huainan coal to reduce the ash fusion temperature,so that the coal can meet the temperature request of the slag-tap technology of Texaco CWM gasification device which has been introduced to Huainan Chemical Group in recent years,and the mechanism was studied in this paper.
添加助熔剂A降低高灰熔融性淮南煤灰熔融温度,使其适合淮化集团近年引入的Texaco水煤浆气化炉的液态排渣工艺温度要求(1 380℃左右),并对其机理进行了初步的探究。
2) Ash fusion point
灰熔融性温度
1.
But it has low ash fusion point, and easily leads to slagging and fouling.
神华煤具有高挥发分、高发热量、低硫、低灰等特点,是优质的动力用煤;但神华煤的灰熔融性温度较低,易导致炉膛受热面的结渣和沾污。
4) ash softening point
灰熔温度
5) fusion temperature
熔融温度
1.
An in-depth study was conducted concerning the fusion temperature and fusion process dynamic characteristics of three representative pairs of ash samples taken from two units of coal water slurry (CWS)-fired boilers.
对取自2台水煤浆锅炉3对各具代表性灰的熔融温度和熔融过程动态特性进行了深入研究。
2.
Plenty of medical glass bottles which were present in medical wastes had rather low fusion temperatures.
实验结果显示,不同化学组分对熔融温度有不同的影响,SiO2能够提高医用玻璃的熔融温度,B2O3和碱金属氧化物(Na2O、K2O)会大幅降低医用玻璃的熔融温度,而碱土金属氧化物(CaO、BaO)和Al2O3会使医用玻璃的软化温度升高,却能使流动温度降低。
6) melting temperature
熔融温度
1.
The melting characteristics and behavior of heavy metals of fly ashes were investigated under different melting temperatures.
对城市垃圾与煤混烧飞灰进行旋风熔融试验,分析了不同熔融温度条件下熔渣的微观形貌及重金属行为。
2.
The influence of fly ash on partition characteristics of heavy metals before and after melting treatment was studied , including the melting temperature, melting time and the basicity.
研究探讨了熔融温度、熔融时间、碱基度对飞灰熔融处理前后重金属分布特性的影响。
3.
The melting temperature,melting heat,static and dynamic mechanical properties of PA6/PTFE blends and PA66/PTFE blends are experimentally investigated in this paper.
PA6/PTFE共混物的熔融温度随PTFE含量的增加而升高,熔融热却随PTFE含量的增加而降低。
补充资料：灰化温度
分子式：
CAS号：
性质：又称分解温度。在原子吸收分析高温石墨炉原子化法的灰化阶段中,为了挥发去除试样中基体组分,石墨炉所需达到的温度。
CAS号：
性质：又称分解温度。在原子吸收分析高温石墨炉原子化法的灰化阶段中,为了挥发去除试样中基体组分,石墨炉所需达到的温度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条