1) bearing siphon wool
轴承油芯
2) bearing core shaft
轴承芯轴
1.
The fractured surface of bearing core shaft of a certain water pump assembly was investigated by means of macroscopic,microscopic and section fractography.
通过对水泵总成中发生断裂的轴承芯轴进行断口的宏观分析、微观分析和剖面分析,及其中各组件的相对位置、表面痕迹和宏观形貌的分析和讨论,分析失效原因,提出改进建议。
3) oil-film bearing
油膜轴承
1.
Study on contact damage of sleeve of oil-film bearing in rolling mill;
大型轧机油膜轴承锥套损伤问题研究
2.
The Oil-film Temperature Fild Analysis of Oil-film Bearing Based on ANSYS;
基于ANSYS的油膜轴承油膜温度场分析
3.
This paper presented the mechanism of fretting fatigue failure that happened on the contact surfaces between sleeve and roll neck of oil-film bearing under the rolling load.
研究了油膜轴承锥套与辊颈接触表面在轧制载荷作用下发生微动疲劳损伤的力学机理。
4) oil film bearing
油膜轴承
1.
Design and analysis of structural parameters for capillary oil film bearing
毛细管节流的油膜轴承结构参数设计分析
2.
A modern large-scale mill's perfect bearing——oil film bearing,a key part of the mill,has many advantages,such as large carrying capacity,long service life,wide speed range,low friction coefficient,small configuration size,strong impact resistance,etc.
现代大型轧机的理想轴承——油膜轴承是轧机的关键部件,具有承载能力大、使用寿命长、速度范围广、摩擦因数小、结构尺寸小、抗冲击能力强等优点。
3.
Baosteel Branch's 5m mill is the first especially wide and heavy plate production line,and oil film bearing is one part of its main equipment.
宝钢分公司厚板厂5m轧机是国内第一条特宽幅厚板生产线,油膜轴承是厚板轧机的主要设备之一,正确认识和掌握其特点是提高厚板生产的关键环节。
5) self lubricating bearings
含油轴承
1.
The partially alloyed CuSn10 powder for high speed,low noise and self lubricating bearingshad been successfully developed by Cu Sn alloying process The characteristics of powders were investigated by SEM The influence of powder mixing process,green density,diffusion time and temperature on the properties of powders were discusse
本文通过对电解Cu粉、雾化Sn粉的部分合金化过程的研究 ,制备出适于制造高速、低噪音、微型含油轴承的CuSn1 0部分合金化粉末。
6) oil bearing
含油轴承
1.
Comparing research has been done between Fe Cu and bronze P/M oil bearings for odometers.
本文针对里程表用含油轴承 ,对粉末冶金铁 铜和青铜材料进行了对比研究。
补充资料：K311八轴挤芯机操作规程
1、遵守铸造设备通用操作规程。
2、检查三角皮带的松紧度与磨损情整，如过紧、过松，或磨损严重，应予调况或更换。
3、先点动试车，然后空运转2-3分钟，检查传动系统（电动机、减速器）以及压杆与塞杆的运动是否正常，确认一切正常后，方可进行生产。
4、工作后，清理设备时，要特别清理料槽中和套筒里的积砂。
2、检查三角皮带的松紧度与磨损情整，如过紧、过松，或磨损严重，应予调况或更换。
3、先点动试车，然后空运转2-3分钟，检查传动系统（电动机、减速器）以及压杆与塞杆的运动是否正常，确认一切正常后，方可进行生产。
4、工作后，清理设备时，要特别清理料槽中和套筒里的积砂。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条