1) bonder flux
粘结焊剂
2) Sticking
粘结
1.
Research into Factors Affected on the Sticking Defects During the Annealing Process for Cold Rolling Strip and Countermeasures;
冷轧带钢退火粘结缺陷影响因素的研究及控制措施
2.
Analysis on Sticking Defect of CSP Cold Rolled Steel Sheet Annealing in Bell Type Annealing Furnace;
CSP冷轧薄板罩式退火过程粘结的分析和工艺改进
3.
Excessive convexity,severe wedge,dissymmetric convexity and partial protrusion will result in sticking of sheets during annealing in the bell-type furnace.
热轧板凸度过大,楔形严重,凸度不对称和有局部高点,均可造成罩式炉退火时产生粘结。
3) adhesion
粘结
1.
Analysis on adhesion defect of silicon steel coil and countermeasures;
硅钢卷粘结成因及消除对策浅析
2.
The linkings of the uncoiler tension,strip thickness,adhesion degree and coil radius on the wrinkles were analyzed.
为了减小带钢表面的横折印缺陷,通过建立平整机开卷过程有限元模型,研究了冷轧带钢钢卷在开卷过程中应力的大小分布及影响因素,分析了开卷张力、板厚、粘结程度和钢卷半径等与产生横折印的关系,提出了减小带钢在打开过程中的反弯和罩式炉中的粘结程度来克服带钢表面横折印缺陷的途径,并发现增大开卷张力有利于减轻或避免横折印的产生,消除了关于开卷张力与横折印关系的错误认识。
3.
The volume fractions of the inter-cell components are calculated and the arrangement and adhesion of the single cells in the technical fibers are also described according to the feature of the cross section.
用化学方法把黄、红麻单纤维从工艺纤维中分离出来,应用计算机图像采集系统,对黄、红麻单细胞纤维的形态进行观察;描述单细胞躯干上的中腔、节点、单细胞直径及长度特征,并通过对截面的观察和截面细胞个数的统计,计算出胞间层的体积含量,推测出单细胞在工艺纤维中的粘结方式,提出黄、红麻工艺纤维细化的有效途径。
4) bonded
粘结
1.
A measured study of post-tensioning bonded prestressed concrete continuous beam;
后张有粘结预应力混凝土连续梁张拉控制参数实测研究
2.
The solid lubricating and wear resistant mechanisms of the bonded solid lubricant organic coatings are analyzed.
分析了有机粘结固体润滑膜的减摩耐磨主要机理,详细讨论了环氧与酚醛环氧、聚酰亚胺与聚酰胺酰亚胺、聚苯硫醚和聚酰胺等常用高分子树脂基体固体润滑膜的摩擦学特性及其性能,展望了高分子固体润滑膜的发展趋势和研究方向。
3.
The bonded magnet from rapid quenched NdFeB has been produced, and the influence of the technique factors such as the kind of binder, formation press and solidification on its properties has been analysed.
采用快淬NdFeB磁粉,通过粘结方法,制备了NdFeB粘结磁体。
5) bond
粘结
1.
Experimental study on bond behaviors between FRP tendons and concrete;
FRP筋与混凝土粘结滑移性能的试验研究
2.
The bond strength between light-cured composite resin and exfoliated surface of base alloy;
光固化复合树脂与金属基底的瓷剥脱面间的粘结强度
3.
Experiment research on bond behavior between deformed bar and lightweight concrete;
陶粒混凝土与变形钢筋粘结锚固性能的试验研究
6) bonding
粘结
1.
The reasons and preventive measures of Tangsteel's FTSC thin slab continuous casting bonding;
唐钢FTSC工艺薄板坯连铸粘结的原因及预防措施
2.
Microstructure and magnetostrictive property of bonding TbDyFe alloy;
粘结TbDyFe合金的组织及磁致伸缩性能
3.
Micromorphological structures and microleakage investigation of resin bonding to deproteinized dentin;
树脂与无机改性牙本质的粘结界面及其微漏研究
参考词条
补充资料：焊剂
颗粒状焊接材料。在焊接时它能够熔化形成熔渣和气体，对熔池起保护和冶金作用。焊剂由大理石、石英、萤石等矿石和钛白粉、纤维素等化学物质组成。焊剂主要用于埋弧焊和电渣焊。用以焊接各种钢材和有色金属时，必须与相应的焊丝合理配合使用，才能得到满意的焊缝。焊剂分为酸性、中性和碱性3种,按制造方法分为熔炼焊剂和非熔炼焊剂。熔炼焊剂是用各种矿石经电弧炉熔炼后粉碎而成。其中，酸性熔炼焊剂应用较多，它配以适当的焊丝，广泛用于碳钢和低合金结构钢的焊接。中性和碱性熔炼焊剂则用于强度较高的高强钢焊接。非熔炼焊剂制造简单，劳动卫生条件较好，质量容易控制，并可加入各种所需合金元素来改善焊缝金属组织和性能，因而得到较广泛的应用。非熔炼焊剂烘干温度在 400℃以下的，称为粘结焊剂；烘干温度在400～1000℃的,称为烧结焊剂，后者强度好，成品率高，应用较多。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。