2) wear mechanism
磨损机制
1.
Two body abrasive wear mechanism of TiNi SMA;
TiNi 系形状记忆合金两体磨粒磨损机制研究
2.
Wear resistance and wear mechanism of TiC_P/Ti6Al4V composite;
TiC_P/Ti6Al4V复合材料的耐磨性及磨损机制
3.
Their mechanical properties and tribological performance were investigated,and the wear mechanism was discussed.
采用冷压烧结方法制备了短碳纤维增强锡青铜基自润滑复合材料和ZQSn663锡青铜,对其力学性能及摩擦磨损性能进行了对比研究,并对磨损机制进行了讨论。
3) friction and wear mechanism
磨损机理
1.
And the friction and wear mechanisms were also discussed.
采用粉末冶金方法制备了ＳｉＣ颗粒增强铁基复合材料，考察了ＳｉＣ颗粒含量与铁基粉末冶金复合材料的显微组织、相对密度、力学性能及磨损性能之间的关系，并探讨了其摩擦磨损机理。
4) wear mechanisms
磨损机理
1.
The wear mechanisms of 45 are mainly abrasive wear and adhesive wear.
磨损机理主要为磨粒磨损和粘着磨损。
2.
In this paper,category ization\,tribology properties and wear mechanisms of heat resistance polymer composites are reviewed.
本文综述了耐温聚合物基复合材料的种类、摩擦学性能和磨损机理。
5) mechanical wear
机械磨损
1.
The results show that the friction coefficient and wear loss of the brushes due to electrical wear are higher than those due to mechanical wear.
研究了以上3种复合材料电刷在相同的压力和线速度条件下的机械磨损性能和电磨损性能。
2.
The results show that the wear volume loss of composites increases with the increase of pressure under mechanical wear,but the wear volume loss of composites varies with the change of pressure by U shape under electrical wear.
研究了压力变化对碳纳米管银石墨复合材料纯机械磨损和电磨损性能的影响。
3.
These factors main have mechanical wear and corrosion wear.
主要有机械磨损和腐蚀磨损。
6) wearing mechanism
磨损机理
1.
Research on the Wearing Mechanism of TiN-coated Tools for High-speed Turning & Milling with Water-soluble Coolant;
湿式高速车铣时TiN涂层刀具的磨损机理研究
2.
Research on Wearing Mechanism of Ceramic Tool in High Speed Dry Turning and Milling;
干式高速车铣时金属陶瓷刀具磨损机理研究
3.
A study on wearing mechanism and Finite Element Analysis of centrifugal slurry pump;
离心式渣浆泵叶轮磨损机理研究及强度的有限元分析
补充资料：表面磨损
分子式：
CAS号：
性质：两表面接触并作相对运动所产生的微弱摩擦导致了缓慢的材料消耗。根据相对运动的特点，分成滑动磨损，转动磨损，冲击磨损三种。通常认为接触压力较小，表面材料消耗不大的属表面磨损，相反的情况，可归入表面磨耗。
CAS号：
性质：两表面接触并作相对运动所产生的微弱摩擦导致了缓慢的材料消耗。根据相对运动的特点，分成滑动磨损，转动磨损，冲击磨损三种。通常认为接触压力较小，表面材料消耗不大的属表面磨损，相反的情况，可归入表面磨耗。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条