1) cocure process
共固化工艺
1.
Experimental study of the cocure process with the vacuum bag method for honeycomb sandwich structure;
蜂窝夹层结构真空袋共固化工艺过程实验研究
2) curing process
固化工艺
1.
The technoloies progress about organic passivation,roll coater and curing process of chromate-free organic passivation for galvanizing sheet steel were summarized.
概述了国内外镀锌钢板有机无铬钝化技术涉及的有机钝化剂、涂覆与固化工艺研究的进展。
2.
The curing process of KH- 304 resin matrix composites is studied in this paper.
本文研究了ＫＨ—３０４树脂基复合材料的固化工艺，指出加压点必须选在树脂粘度最低之前。
3.
The curing processes were analyzed and the XRD and microstructure of the composites were analyzed.
67μm范围的钛酸钡(BaTiO3)作为高介电填充组分,采用溶液共混合旋涂工艺,制备了不同BaTiO3含量的0-3型BaTiO3/环氧复合材料膜,研究分析了环氧树脂固化工艺的确定以及不同BaTiO3含量的复合材料的晶相及显微结构。
3) curing technology
固化工艺
1.
Influence research of curing technology by orthogonal test on mechanical properties of carbon fiber reinforced composite;
固化工艺对碳纤维增强复合材料力学性能影响的正交试验研究
2.
The curing technology of the TDE-85/MeTHPA resin modified by polyurethane was discussed by DSC curve and IR atlases.
采用该预聚体、扩链剂、交联剂对TDE-85/甲基四氢邻苯二甲酸酐(MeTHPA)树脂体系进行改性,通过红外光谱和示差扫描量热法(DSC)分析,探讨与确定了聚氨酯改性环氧树脂体系固化工艺条件。
3.
The effect of these facters on bonding strength had been tested to obtain the best curing technology parameters of the adhesive with low viscosity for building to the desirable bonding quality,meeting with the project problems.
对影响建筑结构胶粘接强度的各工艺参数进行了试验研究,确定了低粘度结构胶最佳固化工艺参数,并结合工程施工提出相应解决措施。
4) curing procedure
固化工艺
1.
Effect of curing procedure on the impact toughness of adhesively bonded joints
固化工艺对胶接接头冲击性能的影响
2.
In this paper,the main factors such as metal fillers,curing procedure and pigments that influence the emissivity of the infrared shielding coatings were studied.
对金属填料、涂层固化工艺以及着色颜料等因素对涂料红外发射率的影响开展了实验研究,结果表明:随着铝粉含量增加,发射率降低;酚醛-铝粉体系最佳固化温度为60℃,固化时间为12 h;选择硫化镉为着色颜料,含量不超过2%(质量分数)可以满足可见红外兼容。
5) curing technique
固化工艺
1.
The effects of type and amount of curing accelerants on the curing reaction of A80/ Novolac,A80/BPAN and A80/BPFN have been studied with the method of DSC and curing techniques are also determined.
采用动态DSC方法研究了促进剂种类、促进剂用量对A80/Novolac、A80/线型双酚A酚醛(BPAN)和A80/线型双酚F酚醛(BPFN)体系固化反应的影响规律,并确定了固化工艺条件。
6) solidification process
固化工艺
1.
This paper discusses the patterns and the phase boundaries of rubber domains in the modified epoxy concrete under the various technological conditions, by meansof changing the solidification processes and using the method of micro-phase analysis.
通过改变固化工艺，采用显微图相分析手段，探讨了改性环氧树脂混凝土中橡胶分散相在不同工艺条件下的形态和相界面。
补充资料：化学共沉淀工艺
分子式：
CAS号：
性质：化学法制取陶瓷等粉料的一种工艺。原料各组分以溶液状态按给定配比混合均匀。加入适宜的沉淀剂(如氢氧离子、碳酸盐离子、硫酸盐离子、草酸盐离子等)，使各组分离子形成不溶性氢氧化物、碳酸盐、硫酸盐、草酸盐等的共沉淀物。再以大量蒸馏水冲洗，除去有害杂质。然后在一定温度下焙烧。可获得高纯超细粉料。为防止颗粒团聚，沉淀过程中常加入分散剂等有机表面活性物质。用此法已制得具有化学计量组成的、烧结性能良好的钛酸钡、钛酸铅、铁酸锰(MnFe2O4)等粉料。此法设备简单、较为经济，便于大中型工业化生产。已获得广泛应用。
CAS号：
性质：化学法制取陶瓷等粉料的一种工艺。原料各组分以溶液状态按给定配比混合均匀。加入适宜的沉淀剂(如氢氧离子、碳酸盐离子、硫酸盐离子、草酸盐离子等)，使各组分离子形成不溶性氢氧化物、碳酸盐、硫酸盐、草酸盐等的共沉淀物。再以大量蒸馏水冲洗，除去有害杂质。然后在一定温度下焙烧。可获得高纯超细粉料。为防止颗粒团聚，沉淀过程中常加入分散剂等有机表面活性物质。用此法已制得具有化学计量组成的、烧结性能良好的钛酸钡、钛酸铅、铁酸锰(MnFe2O4)等粉料。此法设备简单、较为经济，便于大中型工业化生产。已获得广泛应用。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条