1) HISYS-HS32002
汉芯-HS32002
2) character memory chip
汉字库芯片
1.
It mainly applies to personal character memory chip.
本软件主要应用于制作合乎个性要求的专用汉字库芯
3) Han
[英][hæn] [美][hɑn]
汉
1.
Study of HLA polymorphism in the 6965 Han bone marrow registry donors;
6965名汉族骨髓供者HLA多态性分析
2.
Aesthetic Connotations and Ideological Foundations of "Fafen Doctrine" in the Han Dynasty;
汉代“发愤说”的美学内涵及思想基础
3.
Discuss the Formation and Vicissitude of the Han s and Hun s National Consciousness from the Angle of the Relationship between Han and Hun;
从汉匈关系的角度探讨汉匈民族意识的形成与变迁
4) Han Dynasty
汉
1.
The prevailing customs of Qin Dynasty and Han Dynasty touches the emotion—An analysis on the emotional factors and aesthetic orientation of the sculptures of Qin Dynasty and Han Dynasty;
秦风汉韵总关情——析秦汉雕塑的情感因素与审美走向
2.
Discussion of "Fangzhong Music" and "Fangzhong Songs" in Han Dynasty;
论汉代的“房中乐”、“房中歌”
3.
On the Exploitation in BaShu Area During Han Dynasty to Tang Dynasty;
汉唐间巴蜀地区开发研究
5) Chinese
[英]['tʃai'ni:z] [美]['tʃaɪ'niz]
汉
1.
On the Different Thinking Patterns between English and Chinese in Light of Zi as the Basic Structural Unit of Chinese;
英汉思维差异的“字本位”视角
2.
About English abbreviations "invasion" of Chinese;
英语缩略语“入侵”汉语的思考
补充资料:Z8612热芯盒射芯机操作规程
1、遵守铸造设备通用操作规程。
2、工作前还必须遵守:
a、
检查设备上行程开关和碰块的位置是否正确,如不正确,必须调整。
b、
接通电源,打开压缩空气伐门,先用手动方法,对各机构逐进行点动试车,然后用自动方法,进行一个循环试车,确认一切正常后,方可进行生产。
3、工作中还必须遵守:
a、
在设备开动后,一个循环未完成时,不许中途调整电器,以免发生误动作,造成设备人身事故;
b、
设备的每一个循环后,必须用喷咀清除芯盒上残存的砂子,并喷涂分型剂;
c、
在未切断电源和所气源前,不准将手伸入芯盒和夹紧器之间的空隙处,或把手放在导轨上,以免发生人身事故。
d、 一般不准空射,如必须空射,一定要把压缩空气伐门关小;
e、 如果用手操作,不准同时操作两个电器开关。
4、工作后还必须遵守:
a、
操纵各个电器开关,使设备各机构恢复到原始位置,然后切断电源和气源;
b、 折下射砂头,清理积砂和粘砂;
c、 清除排气塞内的粘砂;
d、
取下射砂筒,清除缝隙中的粘砂,最后用石蜡涂擦内壁,但不要将缝隙堵塞;
e、 清除闸板上的积砂,并在闸板上涂石墨粉,以减少磨擦;
f、 清除导轨和导杆上的积灰和积砂,并涂上一层润滑油。
2、工作前还必须遵守:
a、
检查设备上行程开关和碰块的位置是否正确,如不正确,必须调整。
b、
接通电源,打开压缩空气伐门,先用手动方法,对各机构逐进行点动试车,然后用自动方法,进行一个循环试车,确认一切正常后,方可进行生产。
3、工作中还必须遵守:
a、
在设备开动后,一个循环未完成时,不许中途调整电器,以免发生误动作,造成设备人身事故;
b、
设备的每一个循环后,必须用喷咀清除芯盒上残存的砂子,并喷涂分型剂;
c、
在未切断电源和所气源前,不准将手伸入芯盒和夹紧器之间的空隙处,或把手放在导轨上,以免发生人身事故。
d、 一般不准空射,如必须空射,一定要把压缩空气伐门关小;
e、 如果用手操作,不准同时操作两个电器开关。
4、工作后还必须遵守:
a、
操纵各个电器开关,使设备各机构恢复到原始位置,然后切断电源和气源;
b、 折下射砂头,清理积砂和粘砂;
c、 清除排气塞内的粘砂;
d、
取下射砂筒,清除缝隙中的粘砂,最后用石蜡涂擦内壁,但不要将缝隙堵塞;
e、 清除闸板上的积砂,并在闸板上涂石墨粉,以减少磨擦;
f、 清除导轨和导杆上的积灰和积砂,并涂上一层润滑油。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条