1) binder
粘结胶
1.
In this paper, through the design of backrest and the relation of specific property and use of two binders, the way of angle precision of prisms is guaranteed in the mass serial production is presented.
本文通过对靠体的设计和对二种粘结胶的特性及作用的论述，提出了在大批量生产中如何才能保证棱镜角度精度的方
2) glue
粘结胶浆
3) bonding cement
粘结胶泥
4) inorganic binding material
无机粘结胶
1.
Performances of inorganic binding material and its application —an ideal material for remedying and reinforcing concrete works;
一种用于混凝土修补的无机粘结胶的性能及应用
5) Sticking
粘结
1.
Research into Factors Affected on the Sticking Defects During the Annealing Process for Cold Rolling Strip and Countermeasures;
冷轧带钢退火粘结缺陷影响因素的研究及控制措施
2.
Analysis on Sticking Defect of CSP Cold Rolled Steel Sheet Annealing in Bell Type Annealing Furnace;
CSP冷轧薄板罩式退火过程粘结的分析和工艺改进
3.
Excessive convexity,severe wedge,dissymmetric convexity and partial protrusion will result in sticking of sheets during annealing in the bell-type furnace.
热轧板凸度过大,楔形严重,凸度不对称和有局部高点,均可造成罩式炉退火时产生粘结。
6) adhesion
粘结
1.
Analysis on adhesion defect of silicon steel coil and countermeasures;
硅钢卷粘结成因及消除对策浅析
2.
The linkings of the uncoiler tension,strip thickness,adhesion degree and coil radius on the wrinkles were analyzed.
为了减小带钢表面的横折印缺陷,通过建立平整机开卷过程有限元模型,研究了冷轧带钢钢卷在开卷过程中应力的大小分布及影响因素,分析了开卷张力、板厚、粘结程度和钢卷半径等与产生横折印的关系,提出了减小带钢在打开过程中的反弯和罩式炉中的粘结程度来克服带钢表面横折印缺陷的途径,并发现增大开卷张力有利于减轻或避免横折印的产生,消除了关于开卷张力与横折印关系的错误认识。
3.
The volume fractions of the inter-cell components are calculated and the arrangement and adhesion of the single cells in the technical fibers are also described according to the feature of the cross section.
用化学方法把黄、红麻单纤维从工艺纤维中分离出来,应用计算机图像采集系统,对黄、红麻单细胞纤维的形态进行观察;描述单细胞躯干上的中腔、节点、单细胞直径及长度特征,并通过对截面的观察和截面细胞个数的统计,计算出胞间层的体积含量,推测出单细胞在工艺纤维中的粘结方式,提出黄、红麻工艺纤维细化的有效途径。
参考词条
补充资料：Sds-聚丙烯酰胺凝胶电泳凝胶电泳
sds-聚丙烯酰胺凝胶电泳（sds-page，sodium dodecyl sulfate-polyacrylamide gel electrohoresis）
在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的，而不是根据分子所带的电荷和大小分离的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。