1) External collapse load
外挤载荷
1.
Effects of cement sheath elastic modulus on casing external collapse load;
水泥环弹性模量对套管外挤载荷的影响分析
2) extrusion load
挤压载荷
1.
The influence of the curvature angle ψ of the outside corner on the extrusion load and the deformation uniformity was discussed.
运用有限元方法对纯铝的等径弯角挤压(ECAE)过程进行了模拟计算,探讨了挤压通道外接圆弧角ψ对挤压载荷及试样变形均匀度的影响。
3) external load
外部载荷
1.
It changes the external load into the internal force of the cooling bed and gets rid of it.
将外部载荷转化为冷床自身内力消除掉。
2.
A method to determine the car s wheel-bearings external load(CWEL) was developed from this model and the characteristic of the CWEL was presented.
采用基于轿车线性化刚体运动的稳态转弯模型对轮毂轴承外部载荷进行推导计算,进而对轴承外部载荷的特性进行了分析。
4) external loads
外载荷
1.
In this article, a calculation model is madeup in which the external loads are considered in reinforcement design through Equal-area method.
对于低压高塔,按标准提供的等面积方法(仅考虑压力载荷)进行开孔补强设计有时是不安全的,本文针对这一问题,结合工程设计实例和有限元分析,给出了在考虑风载荷、地震载荷等外载荷作用下,按照等面积原则进行开孔补强设计的解决方案。
2.
The external loads on the A-type gate crane foundation and its reinforcement structure are studied.
研究了A型门架基座及加强结构的外载荷,采用有限元法计算了结构在各载荷组合工况下的应力。
3.
In this paper,external loads of hull are predicted by combining theoretical analysis and rule calculation.
文章采用理论计算和规范相结合的方法预报了船体外载荷,采用结构有限元分析法与光弹性试验法相结合的方法,研究了月池开口部位的主甲板和船底板处的应力分布和应力集中系数,为优化月池结构提供了依据。
5) External load
外载荷
1.
We propose a new method for calculating the load and deformation of such components as bolt-shaped rings and flanges which are regarded as integral components and subjected to external load.
将螺栓、O型圈和法兰环作为一个整体,应用弹性理论,提出了在外载荷作用下各元件的受力与变形的计算方法。
2.
On the basis of analysis for submarine plane hatch wallboard external pressure condition,indicate external load of submarine plane hatch wallboard stability verify should not less than submarine pressure hull calculating loa
本文在分析潜艇耐压艇体内部平面舱壁板受力情况的基础上 ,提出平面舱壁板稳定性校核中外载荷应取不低于潜艇耐压艇体的计算载荷P
3.
Through theoretical analysis and simulation testing,demonstrates the formation of the hydraulic system pressure and the relationship between external load,described in detail how to use the FluidSIM hydraulic(pneumatic) simulation software to the process of system pressure and methods.
通过理论分析和仿真测试论证了液压系统的压力形成和外载荷的关系,详细叙述了如何使用FluidSIM液压(气动)仿真软件进行压力测试的过程和方法。
6) infrared payload
红外载荷
1.
Then, three typical infrared payloads of foreign UAVs are presented.
本文首先分析了无人机的军用及民用领域,接着着重介绍了三种国外典型无人机红外载荷,最后对国内的无人机航空遥感系统进行了总结和展望。
补充资料：外外百老汇
见百老汇。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条