1) Elastic contact stiffness
弹性接触刚度
2) sticking contact stiffness
粘性接触刚度
3) contact stiffness
接触刚度
1.
Finite element analysis and application of friction damper tangential contact stiffness
阻尼器切向接触刚度的有限元分析及应用
2.
Study on contact stiffness factor selection method in contact non-linear simulation
接触非线性仿真中接触刚度因子选取的方法研究
3.
Based on truing model of saucer diamond-grinding wheel with cup wheel, the influence of contact stiffness between saucer wheel and cup wheel on the stability of the grinding system and grinding force was discussed, as well as verifying of the signal characteristic and changing rule of grinding force.
在建立杯形砂轮修整碟形金刚石砂轮修整模型的基础上,分析了砂轮接触刚度对磨削系统稳定性和磨削力的影响。
4) contact rigidity
接触刚度
1.
Research for contact rigidity of marine ME s base gasket;
船舶主机机座垫片的接触刚度研究
2.
Through alter the method on scraping contact surface between main spindle head and lathe frame, we may increase contact point and improve the contact rigidity.
通过改进普通车床主轴箱与床身接触面的刮削方法增加接触点，从而提高接触刚度。
3.
Based on the theoretical analysis on some current connecting materials between the ship main engine and its base, the author holds that, in installing main engine of the same type, the casting epoxy shim shows the maximum contact rigidity, and the integral rectangular shim would be the next and the adjusting shim appears to be the minimum, which is not adopted to general circumstance.
对目前使用的几种船舶主机与船体基座的连接方式从理论上进行了分析比较 ,认为在安装同类主机的情况下 ,浇注环氧树脂垫片连接方式的接触刚度最大 ,其次是整块矩形片连接 ,可调式垫片连接方式的接触刚度最小 ,一般情况下 ,不宜采用。
5) elastic contact hardness
弹性接触硬度
1.
573 2;the mean elastic contact hardness coefficient is approximately 3.
573 2,平均弹性接触硬度系数约为3。
6) elastic contact
弹性接触
1.
By improving process technique of screw insert part and application of elastic contact structure,plastic forward in the screw insert and ungrammatical problem of screw insert were successfully resolved.
通过对螺纹嵌件的工艺分析,针对模具设计中存在的问题,提出了反向推理的解决方法,并有针对性地设计出了弹性接触的模具结构。
2.
This work attempts to find a new homogenization method for the analysis of assemblage of elastic contact bodies.
研究工作目的是建立弹性接触颗粒状组成周期性结构材料力学分析的均匀化模型。
3.
Based on the work presented in paper , a new homogenisation method for the analysis of assemblage of elastic contact bodies is proposed in this paper.
基于文献 [1]的工作 ,给出弹性接触颗粒状组成周期性结构材料宏观力学均匀化分析新方法。
补充资料：弹性刚度常数
分子式：
CAS号：
性质：又称弹性劲度常数。弹性体在单位应力下发生的应变。是弹性体刚度的一种量度。通常用Cij表示，单位为Pa，由于压电体存在二极压电效应，在电学条件不同时，所测得的弹性刚度常数也不相同。在短路条件下测得的弹性刚度常数，称为短路弹性刚度常数，用表示。在开路条件下测得的弹性刚度常数，称为开路弹性刚度常数，用表示。弹性刚度常数共用10个，即、、、、和、、、和。压电陶瓷是弹性体，可用弹性刚度常数进行评价。弹性刚度常数值愈小，弹性体愈容易形变；其值较大，材料比较刚硬。
CAS号：
性质：又称弹性劲度常数。弹性体在单位应力下发生的应变。是弹性体刚度的一种量度。通常用Cij表示，单位为Pa，由于压电体存在二极压电效应，在电学条件不同时，所测得的弹性刚度常数也不相同。在短路条件下测得的弹性刚度常数，称为短路弹性刚度常数，用表示。在开路条件下测得的弹性刚度常数，称为开路弹性刚度常数，用表示。弹性刚度常数共用10个，即、、、、和、、、和。压电陶瓷是弹性体，可用弹性刚度常数进行评价。弹性刚度常数值愈小，弹性体愈容易形变；其值较大，材料比较刚硬。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条