1) superheat
[英]['su:pəhi:t] [美]['sʊpɚhit]
过热度
1.
Fuzzy control for superheat of evaporator based on variable-universe method;
基于变论域理论的蒸发器过热度的模糊控制
2.
Effects of superheat and current density on electrolysis expansion performance of semi-graphitic cathode at low temperature
过热度和电流密度对半石墨质阴极低温电解膨胀性能的影响
3.
Research on Superheat Control of Molten Steel During Twin-roll Strip Casting
双辊薄带铸轧过程钢液过热度控制研究
2) degree of superheat
过热度
1.
Control of degree of superheat and the practices of anhydrous aluminium fluoride
过热度的控制与无水氟化铝的实践应用
2.
To stabilize the degree of superheat may make the cavity of cell to be more stable.
稳定过热度可以使铝电解槽炉膛趋于稳定,精准的换极、出铝操作及合理的热损失分布有利于炉膛趋于规整,提高电解槽运行的稳定性。
3.
The causes of formation of centerline segregation in bloom bearing steel continuously cast at the Special Steel Plant are analyzed,with the influences of the degree of superheat of the tundish hot metal,etc.
对莱钢特钢厂连铸生产的大方坯轴承钢中心偏析的成因进行分析,探讨中间包钢水过热度等对中心偏析的影响,并在生产实践中提出了预防措施。
3) superheat degree
过热度
1.
Control strategies for the superheat degree of intermediate point temperature in ultra-supercritical power units;
超(超)临界机组中间点温度过热度控制策略
2.
The influence of the different superheat degrees on solidification structure of the Al-5%Cu alloy by electric pulse modification was studied.
研究了不同的过热度对电脉冲孕育处理Al-5%Cu合金凝固组织的影响。
3.
The electronic expansion valve (EEV) was adopted and combination regulation scheme including open loop propor- tional control based on solar radiation intensity and closed loop feedback PI control based on superheat degree of solar collector was determined through experimental research,special parameters were con- firmed for controlling th.
本文以电子膨胀阀作节流元件,采用太阳辐射强度的开环比例控制与集热板过热度的闭环反馈PI控制相结合的控制方案,通过实验研究的方法逐步制定控制策略,分三种不同情况采取特定参数控制集热板出口过热度。
4) overheat
[英][,əʊvə'hi:t] [美]['ovɚ'hit]
过热度
1.
Statistical study on the effects of overheat and casting speed on cleanliness of rolled products;
连铸钢液过热度和拉速对轧材纯净度影响的数理统计研究
2.
By improvement of the temperature hold conditions at the steel ladle and tundish and by selection of the optimal temperature mode in LF furnace,a consistent and low overheat result can be achieved in the process of casting the high carbon steel at low speed and therefore the carbon segregation in the slab can be effectively redu.
通过改善钢包、中包的保温效果,并采用合理的LF炉温度控制模式,可以使高碳钢在进行低拉速浇铸时获得稳定且较低的过热度,从而有效降低铸坯碳偏析。
3.
Throug analyzing,the producing causes of inner crack are unreasonable contributing water system at secondary cooling zone and high overheat of liquid steel.
济钢一炼钢方坯铸机提高拉坯速度后出现了铸坯内部裂纹，分析其原因是二冷配水制度不合理以及钢水过热度高，为此在保证钢水流动性良好的条件下采用低过热度浇注工艺，同时采取中间包扩容，改进结晶器及二次冷却系统等措施，使铸坯鼓肚现象基本消除，方坯内部裂纹发生率由３０％降到２。
5) superheating
[英]['su:pəhi:t] [美]['sʊpɚhit]
过热度
1.
In the blowing bath metal superheating should be within 60℃~120℃, according to the steel grade smelted.
吹炼过程中,熔池金属过热度应在60℃～120℃范围内;终点钢水过热度由所炼钢种的要求而定。
2.
It was found that the crystalline structure features ofthe seedfilm havestrong relationships with the degree of superheating and the melting behavior.
结果表明,YBCO薄膜的微结构对于其过热度以及整个薄膜熔化的过程有很大的影响,高品质的薄膜具有低界面缺陷比率,由此导致了其在熔化过程中较高的过热度。
3.
The paper has studied main reasons such as SEN clogging,superheating,steel composition and technology of blowing argon and refining etc.
本文从水口堵塞、过热度、钢水成分、吹氩和精炼工艺等方面研究了影响钢水流动性的原因,采取如下措施:1)控制钢水温度的精准性,合理控制炉前出钢温度,合理调度生产节奏;2)严格控制硅含量、锰含量和铝含量,确保实现夹杂物的变性效果;3)保证足够的精炼时间,避免或减少精炼炉二次吸氮,根据精炼不同阶段的冶金功能,采取不同的吹氩制度和强化喂线过程的监控;4)避免钢水在浇铸过程中发生二次氧化,严格执行浇铸过程中的保温措施。
6) over-heating
过度加热
1.
In recent years,Chinese processing tomato industry had developed expeditiously,especially Xinjiang tomato paste processing is outstanding,but there are a lot of profound problems in these,such as the over-heating of tomato paste processing.
近些年,我国番茄加工产业有了迅猛的发展,其中尤以新疆番茄加工产业(番茄酱)的生产最为突出,这其中也存在一些深层次的问题,如番茄酱生产中的“过度加热”等,都有待食品方面的专业人士加以研究、探讨和解决。
补充资料：热度
1.热的程度;温度。 2.指高于正常的体温。 3.犹热情。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条