1) thick plate
厚板
1.
Welding technology of Cu-Ni alloy B10 thick plate;
Cu-Ni合金B10厚板焊接工艺
2.
Friction-stir welding on thick plate of 7A52 aluminum alloy;
7A52铝合金厚板搅拌摩擦焊
3.
Prediction of angular distortion in thick plate multi-pass weld;
厚板多层多道焊角变形分析方法
2) heavy plate
厚板
1.
Practice of improving the profile shape and performance of heavy plate;
提高厚板板形质量和性能的实践
2.
Research of deficient deformation leveling model in heavy plate;
厚板不充分变形矫直工艺方案研究
3.
TMCP process was applied to the rolling of 70mm-thick Q345C heavy plate steel to control its strength,ductility and toughness.
结果表明,采用该无热处理的未再结晶区大压下量TMCP工艺试验的厚板,轧后无论采用空冷还是加速冷却,力学性能都满足GB/T1591-94的要求,且厚度方向力学性能均匀性良好;加速冷却钢板铁素体晶粒细化更为明显,表面与心部铁素体晶粒尺寸稍有差异。
3) plate
[英][pleɪt] [美][plet]
厚板
1.
Construction and reform/expansion of aluminum alloy plate worldwide;
世界铝厚板系统的建设与改扩建
2.
The effects of total deformation on the microstructure and room temperature tensile properties of BT-20 alloy plate were studied in α+β.
主要研究了在α+β区总变形量对BT-20钛合金厚板组织与性能的影响,获得了在两相区总变形量控制在71%、85%和91%生产出的三种规格厚板在相同热处理制度下的显微组织以及所对应的室温力学性能。
3.
The effects of four typical structures on the mechanical properties, impact ductility and fracture toughness etc of BT-20 alloy plate were studied under the conditions of room & high temperature.
主要研究了BT-20钛合金厚板4种典型组织对室温、高温力学性能、冲击和断裂韧度等性能的影响。
4) thick plates
厚板
1.
The natural transverse vibrations of rectangular thick plates with viscoelastic on viscoelastic foundation;
粘弹性基础上粘弹性矩形厚板的固有横振
2.
Structures refinement of Al-Zn-Mg-Cu-Cr alloy thick plates;
Al-Zn-Mg-Cu-Cr合金厚板组织细化
3.
Displacement fundamental equations of the thick plates bending and the general solution to simply supported rectangular plates by transvers shearing defomation
考虑横向剪切变形厚板弯曲的位移型方程及简支矩形板的一般解
5) thick slab
厚板
1.
thick slab transfer and the detailing are mainly discussed.
本文介绍了该工程的结构设计要点,着重阐述了厚板转换及相应的构造措施。
2.
The design method of thick slab of transferring storey of the commercial and dwelling building is introduced, and the measures of the main technical issues are presented in this paper.
对某商住楼结构转换层厚板的设计理念和一些主要技术问题的处理方法进行了探讨。
6) Plate thickness
板厚
1.
According to characteristic of the rolling technology of plate belted steel and the control requirement to steel shape and plate thickness, this paper proposes a decoupling control method based on neural network, and designs an intelligent decoupling controller with self-adapton and self-study decoupling ability.
根据板带钢轧制工艺的特点和板形板厚的控制要求,本文提出了一种基于神经网络的解耦控制方法,并设计了具有自适应、自学习解耦能力的智能解耦控制器。
2.
The microstructures of continuous cast hull steel 10CrNiCu with different plate thickness were studied by transmission electron microscopy.
结果表明 ,在同样的热轧和高温回火工艺条件下 ,随板厚的增加 ,钢板组织中除铁素体与珠光体外 ,逐渐出现了贝氏体分解物 ;铁素体晶粒变大 ,晶界上的第二相增多且长大 ;珠光体片层间距离也略有增加。
补充资料：厚板
厚板
heavy plate
houban厚板(heavy plate)厚度在4mm以上的板材。厚钢板的厚度范围为4~12omm，ZOmm以下的常称中厚板，60mm以上的是特厚板，最大厚度可达soomm。厚钢板的宽度范围为600一3800mm，最大可达s000mm。由于船舶制造、桥梁建筑、石油化工、交通运输、军事工业等部门的迅速发展，以及用板料焊接构件、钢管及型钢的广泛应用，需要大量宽而长的优质厚板，因而厚板生产得到迅速发展。(见彩图插页第4页)厚板采用热轧方式生产，在热轧过程中以严格的热轧工艺制度(见厚板生产)保证其组织性能和力学性能;控制温度和清除氧化铁皮尤为重要。厚板材质日益向合金化发展，厚板生产规模日益向大型化发展，厚板轧机则日益向重型化、高速化和自动化方向发展。 (李生智李隆旭)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条