1) plank
[英][plæŋk] [美][plæŋk]
板，厚板
2) thick plate
厚板
1.
Welding technology of Cu-Ni alloy B10 thick plate;
Cu-Ni合金B10厚板焊接工艺
2.
Friction-stir welding on thick plate of 7A52 aluminum alloy;
7A52铝合金厚板搅拌摩擦焊
3.
Prediction of angular distortion in thick plate multi-pass weld;
厚板多层多道焊角变形分析方法
3) plate
[英][pleɪt] [美][plet]
厚板
1.
Construction and reform/expansion of aluminum alloy plate worldwide;
世界铝厚板系统的建设与改扩建
2.
The effects of total deformation on the microstructure and room temperature tensile properties of BT-20 alloy plate were studied in α+β.
主要研究了在α+β区总变形量对BT-20钛合金厚板组织与性能的影响,获得了在两相区总变形量控制在71%、85%和91%生产出的三种规格厚板在相同热处理制度下的显微组织以及所对应的室温力学性能。
3.
The effects of four typical structures on the mechanical properties, impact ductility and fracture toughness etc of BT-20 alloy plate were studied under the conditions of room & high temperature.
主要研究了BT-20钛合金厚板4种典型组织对室温、高温力学性能、冲击和断裂韧度等性能的影响。
4) Plate thickness
板厚
1.
According to characteristic of the rolling technology of plate belted steel and the control requirement to steel shape and plate thickness, this paper proposes a decoupling control method based on neural network, and designs an intelligent decoupling controller with self-adapton and self-study decoupling ability.
根据板带钢轧制工艺的特点和板形板厚的控制要求,本文提出了一种基于神经网络的解耦控制方法,并设计了具有自适应、自学习解耦能力的智能解耦控制器。
2.
The microstructures of continuous cast hull steel 10CrNiCu with different plate thickness were studied by transmission electron microscopy.
结果表明 ,在同样的热轧和高温回火工艺条件下 ,随板厚的增加 ,钢板组织中除铁素体与珠光体外 ,逐渐出现了贝氏体分解物 ;铁素体晶粒变大 ,晶界上的第二相增多且长大 ;珠光体片层间距离也略有增加。
5) thickness
[英]['θɪknəs] [美]['θɪknəs]
板厚
1.
Textures distribution through the thickness after conventional rolling, cross shear rolling and two direction cross shear rolling were studied by X - ray diffraction technique ( ODF analysis) .
对各主要冷轧织构组分:Brass({110}<112>)、S({123}<634>)、R/S({124}<211>)、Goss({110}<001>)和copper({112}<111>),在三维取向空间的取向密度ω(g)沿板厚的分布进行了定量测定。
2.
This paper is based upon the theory of modern Intellective-Control, introduces the application of Artificial Neural Network (ANN) in the thickness &.
板厚、板形是板带生产中的两个主要指标,文章基于现代智能控制理论,介绍了人工神经网络在板厚、板形控制中的应用,并给出了实验仿真结果。
3.
Comparing the numerical simulation result with that of the experiment,studied the effect of the inertial effect on the result of simulation with the tool s stamping speed,and studied the relation of thickness and the largest permitted speed in the simulation.
本文建立了不锈钢焊管弯曲成形的有限元模型,用动态显示算法对其进行了数值模拟分析, 并用试验对模拟结果进行了验证,研究了随着模拟中设定的冲压速度的变化惯性效应对板材弯曲成形模拟的影响,并通过数值模拟研究了板厚与最大模拟冲压速度的关系,发现板厚越大,模拟中所允许设定的冲压速度越大,在板厚为5mm 时,模拟中最大可设定冲压速度可以达到7000mm/s。
6) board thickness
板厚
1.
This controller based on combined control with constant voltage and constant current supply can realize adaptive control for varying board thickness, compensation of line voltage, display of welding current and voltage, display of workpiece thickness, storage of m.
研究结果说明,该控制器在恒压和恒流控制结合基础上,可实现板厚自适应、网压补偿、焊接电流电压工件厚度显示、多套规范参数储存、故障自诊断和保护功能。
补充资料：厚板
厚板
heavy plate
houban厚板(heavy plate)厚度在4mm以上的板材。厚钢板的厚度范围为4~12omm，ZOmm以下的常称中厚板，60mm以上的是特厚板，最大厚度可达soomm。厚钢板的宽度范围为600一3800mm，最大可达s000mm。由于船舶制造、桥梁建筑、石油化工、交通运输、军事工业等部门的迅速发展，以及用板料焊接构件、钢管及型钢的广泛应用，需要大量宽而长的优质厚板，因而厚板生产得到迅速发展。(见彩图插页第4页)厚板采用热轧方式生产，在热轧过程中以严格的热轧工艺制度(见厚板生产)保证其组织性能和力学性能;控制温度和清除氧化铁皮尤为重要。厚板材质日益向合金化发展，厚板生产规模日益向大型化发展，厚板轧机则日益向重型化、高速化和自动化方向发展。 (李生智李隆旭)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条