1) TiNi alloy
钛镍合金
1.
The Study of Interface Reaction Between TiNi alloy and BN Based Shell Mould used for Investment Casting Titanium;
BN基复合型壳熔模精铸钛镍合金时的界面反应
2.
Continuous cast of TiNi alloy has been realized with homemade equipment consisting of an induction heating with CaO crucible and BN lining of crystallizer.
在自行研制的钛合金连铸装置上进行钛镍合金的连续铸造实验,在感应加热下使用氧化钙坩埚和氮化硼结晶器内衬,通过调整各项工艺参数,实现连续铸造。
3.
The effect of equal channel angular extrusion(ECAE)treatment on tribological behavior of of TiNi alloy was investigated.
研究了油润滑条件下等径弯角挤压(ECAE)工艺处理对钛镍合金摩擦学性能的影响,并利用扫描电子显微镜(SEM)对钛镍合金材料磨损表面进行了观察和分析。
2) nitinol
['nitinɔl,'nai-]
钛镍合金
1.
Study of reconstruction in the defect of esophagus with the use of artificial prosthesis of nitinol alloy and silicone;
应用钛镍合金-硅橡胶组合式人工食管研究食管重建
2.
Study on Nitinol Electropolishing;
由于表面状态对钛镍合金性能具有重要影响,近年来表面改性研究成为人们关注的热点,其中电化学抛光以其特有的优点越来越受到重视。
3) Ti-Ni alloy
钛镍合金
1.
A new kind of boron nitride based shell mold used for investment casting titanium alloys was fabricated and the reaction between it and Ti-Ni alloy was investigated.
研究了一种新型钛合金精密铸造用型壳——氮化硼基复合型壳及其与钛镍合金的界面反应和反应层的形成机制。
2.
The practicability on Ti-Ni alloy manufactured by direct electrochemical reduction of TiO2 and NiO oxides was investigated.
研究了利用熔盐电解法从金属氧化物中直接电解制备钛镍合金的可行性。
4) NiTi alloy
镍钛合金
1.
Application of NiTi alloy bronchial occlusive device in bronchial fistula occlusion;
镍钛合金支气管封堵器在支气管瘘封堵中的应用
2.
Phase transformation from austenite to martensite in NiTi alloy strips under uniaxial tension has been observed in experiments and has been numerically simulated as a localized deformation.
单向拉伸镍钛合金带中从奥氏体到马氏体的相变已在实验中观测到,并被看作为局部变形进行了数值模拟。
3.
This paper describes the biomimetic synthesis of calcium phosphate composite coating with chitosan on NiTi alloy.
将高浓度模拟体液5×SBF与壳聚糖溶液相互结合,在预处理后的镍钛合金基体上快速形成了含壳聚糖的钙磷复合涂层。
5) NiTi alloys
镍钛合金
1.
The surfage modification of NiTi alloys grafted by silylation MPEG;
硅烷化甲氧基聚乙二醇接枝改性镍钛合金
2.
A coating on NiTi alloys surfaces was prepared under diethylene glycol dimethyl ether (diglyme) microwave cold-plasma in electron cyclotron resonance conditions.
在微波电子回旋共振低温等离子体条件下,用二乙二醇二甲醚为试剂对镍钛合金进行表面改性。
3.
However, NiTi alloys have high resistance to deformation, low thermo-conductivity, non-uniform deformation during hot processing.
本文着重进行了以下几个方面的研究: 采用DEFORM-3D商用软件对镍钛合金管坯等温挤压过程进行数值模拟分析。
6) nitinol
['nitinɔl,'nai-]
镍钛合金
1.
Experimental Study of Vascular Anastomosis with Nitinol Clip;
镍钛合金吻合夹吻合血管的实验研究
2.
Low cycle fatigue failure with large strain of nitinol has been tested.
对镍钛合金进行了低周大应变疲劳试验,研究了板厚、丝径大小、表面处理工艺、热处理制度、冷热拉伸、形变角幅度、熔炼工艺等对低周疲劳寿命的影响。
3.
Methods The device was constructed from superelastic Nitinol wires tightly woven into two flat disks and sewed with polyester fibers inside,with a pliable loop on the right-atrial-disk of the device,connecting to the delivery cable.
方法自行设计封堵器是由镍钛合金丝编织成的网状结构,外形呈双盘状,其左房面平整,右房面中间凹陷,中央有与推送杆相接的连接袢,内衬有三层聚酯膜。
补充资料:镍铝钛合金块
分子式:暂无
分子量:暂无
CAS号:暂无
性质:暂无
制备方法:暂无
用途:暂无
分子量:暂无
CAS号:暂无
性质:暂无
制备方法:暂无
用途:暂无
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条