说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 加工时间相同
1)  uniform processing time
加工时间相同
2)  processing time
加工时间
1.
Effects of waste tire rubber powder mesh number and processing time to feature of rubber asphalt
废胎胶粉目数和加工时间对橡胶沥青性能影响
2.
The maximum tardiness in three-machine flowshop problem with separated setup,processing and removal time is discussed,where the setup time and removal time steps of the same job can overlap on three machines,but the processing time can not.
以最小化最大延误为目标函数,讨论了三台机器的流水作业问题,其中每个工件的操作由"调整"步、"加工"步以及"移走"步组成,而工件的调整和移走时间都与加工时间相分离,同一个工件的"调整"步和"移走"步在三台机器上可以重叠,但"加工"步不能重叠,并且第一台机器上没有空闲时间,工件一旦开始加工就不允许中断。
3.
In such a case all the workpieces arrive in batches and each batch has exactly m workpieces to which the processing time required for each one depends on the time the batch containing it just arrives.
工件以批方式到达且每个批中有m个工件,每个工件的加工时间随其批的到达而给定且限定在某个时间区间上。
3)  machining time
加工时间
1.
According to the effect of the technological parameter of the surface of abraser waterjet polish part on machining aim,concerning its machining time,target distance,jet pressure,jet rake,abraser grain size,abraser density and flow quantity,related experiments are conducted in this paper by means of orthog-onal experiment.
针对磨料水射流抛光零件表面的工艺参数———加工时间、靶距、射流压力、喷射倾角、磨料粒度、磨料浓度、流量等对加工指标的影响,用正交试验方法,进行有关试验。
2.
Aiming at the disadvantage of the pop NC simulate softwar on the simulation of the machining time, analyzed the add and moderate controlling of the Siemens 840D numerical control system and developed an accurate simulation system of the NC Program’s Machining Time, the precision rate of simulation is up to 90%.
本文简单介绍了飞机结构件数控加工车间的生产特点,指出了程序加工时间仿真精确性在车间生产管理中的重要性。
3.
This paper analyses the machining time error caused by taking the result of programmed feed-in speed (F) multiply interpolation cycle(Ts) as the length of tiny line(ΔL) which is used to approach the arc in the data sampling circular interpolation.
分析了在数据采样法圆弧插补中以程编进给速度F与插补周期Ts的乘积作为微小直线段的长度ΔL来逼近待加工圆弧轮廓所引起的加工时间误差。
4)  processing times
加工时间
1.
Two linear processing time functions used to model the job processing times characterized by position-dependent are discussed,that is p_i(v)=a\-i-b\-iv and p\-i(v)=a\-iv~(-b).
讨论了工件加工时间和排列中位置相关的单机排序问题。
5)  simultaneous processing
同时性加工
6)  machining time
机加工时间
补充资料:加工
  是指对货物进行再生产;受托加工货物,是指委托方提供原料及主要材料,受托方按照委托方的要求制造货物并收取加工费的业务。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条