1) normal force stiffness
法向力刚度
1.
The amplitude ratios of different reflected and transmitted waves were obtained for an imperfect boundary,and deduced for normal force stiffness,transverse force stiffness and perfect bonding.
得到不完全边界上不同反射波和透射波的振幅比,并导出法向力刚度、切向力刚度和完全粘接时的振幅比。
2) normal stiffness
法向刚度
1.
The relationships between the clutch engaging energy consumption and the engaging torsional stiffness,the energy loss factor,the normal stiffness of the 3 .
分析了接合能耗与接合扭转刚度、损失因子、超越离合器三构件的法向刚度、楔角、外力、滚动摩擦系数等因素的关系,同时给出降低接合能耗的措施。
2.
A hyperbolic constitutive model of interface is put forward and the influence of initial tangent and normal stiffness on the settlement of pi.
用三维有限元的方法,考虑了土体的非线性(Drucker-Prager模型)力学性能,对模型桩进行了模拟计算分析,详细讨论了双曲线接触面本构关系的初始切向、法向刚度对桩顶位移及地表沉降的影响。
3.
Test of constant normal stiffness indicates that side resistance is controlled by normal stiffness of pile surface .
研究表明 ,嵌岩段侧阻力受桩表面的法向刚度所控制 ,嵌岩段的单位极限侧阻力受嵌岩比的影响不大 ,规范上的公式不完全适合软岩嵌岩
3) transverse force stiffness
切向力刚度
1.
The amplitude ratios of different reflected and transmitted waves were obtained for an imperfect boundary,and deduced for normal force stiffness,transverse force stiffness and perfect bonding.
得到不完全边界上不同反射波和透射波的振幅比,并导出法向力刚度、切向力刚度和完全粘接时的振幅比。
4) Normal dynamic stiffness
法向动刚度
5) gravity stiffness method
重力刚度法
1.
To probe into the effect of change in structural parameters,the gravity stiffness method was extended and used to investigate the characteristics of vertical deformation of multi-span suspension bridges.
为了解不同结构参数对连续超大跨悬索桥的影响,对重力刚度法进行了推广,研究了连续超大跨悬索桥体系的静力刚度特征。
6) dynamic stiffness method
动力刚度法
1.
For free vibration analysis of skeletal structures, dynamic stiffness method (DSM) is an exact method.
在杆系结构的自由振动分析中,动力刚度法(DSM)是一种精确的算法。
补充资料：JPZ型三向等刚度橡胶减震器
分子式：
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条