1) Tα= alpha temperature; heat distortion temperature.
阿尔法温度;热畸变温度。
2) heat distortion temperature
热畸变温度
3) temperature distortion
温度畸变
1.
The calculated effect of combined distortion on the engine stability shows that the critical values of pressure and temperature distortion are 8.
压力和温度组合畸变对某涡轮风扇发动机稳定性影响的数值研究表明,该发动机的进口临界压力畸变强度和临界温度畸变强度分别为8。
2.
This paper uses the effective distortion-transfer model to present the numerical investigation on the effect of the inlet temperature distortion upon the stability and performance of an aero-engine.
本文采用有效的畸变传递模型,就进气温度畸变对某发动机稳定性和性能的影响进行了较深入的数值研究,详细地分析了温度畸变对发动机稳定性和性能的影响,探讨了温度畸变在发动机系统中的传递和分布情况。
3.
It also studies the high frequency response temperature measurement and data processing in aero-engine inlet temperature distortion test.
本文详细介绍了高频响温度传感器的设计、校准、误差分析及修正技术,并结合发动机进气温度畸变试验研究了高频响温度测试技术和数据处理方法,对航空发动机稳定性评定试验研究具有重要的指导意义。
4) temperature distortion generator
温度畸变发生器
1.
This paper discusses the constitution and principle of temperature distortion generator.
介绍了温度畸变发生器的组成及工作原理。
5) HDT
热变形温度
1.
In this paper,several terms of thermal- setting resin are covered in detail, including HDT,Martin Temperature, Tg, insulating grade temperature & anti - corrosion application temperature, which is quite beneficial to resin choice or proper resin application.
通过对热固性树脂的热变形温度、马丁耐热、玻璃化转变温度、绝缘耐热等级以及耐腐蚀使用温度五个温度概念的辨析,帮助人们在使用过程中理清头绪,正确选择树脂,有效应用于实际生产。
2.
The effect of wollastonite on the HDT and mechanical properties of PP,and the effect of LDPE on the HDT and mechanical properties of PP/wollastonite composites were investigated.
将PP与高填充量的硅灰石通过双螺杆挤出机熔融共混制得了PP/硅灰石复合材料;将PP/硅灰石复合材料与LDPE通过双螺杆挤出机进行二次共混制得了PP/LDPE/硅灰石三元复合材料;研究了硅灰石对PP的热变形温度(HDT)和力学性能的影响以及LDPE对PP/硅灰石复合材料HDT和力学性能的影响。
6) Heat Distortion Temperature
热变形温度
1.
Its heat distortion temperature reached to 265 ℃.
利用正交试验优选了树脂配方,该树脂体系在有效降低粘度的同时,还提高了耐热性,优选配方树脂体系的热变形温度达到265℃。
2.
The heat distortion temperature and notched impact strength of flame-resistant PA was enhanced highly,and the elongation rate and notched impact strength of flame-resistant PP was upgraded greatly,meanwhile the apparence of products was improved.
在矿物增强阻燃复合材料中引入稀土表面改性剂对无机粉体进行活化处理,在保持阻燃性能的前提下,改善了阻燃剂及无机粉体材料与高分子材料的相容性,显著提高了阻燃PA材料的热变形温度和缺口冲击强度,明显提升了阻燃PP材料的伸长率和缺口冲击强度,产品表观状态也得到大幅度改善,阻燃复合材料的综合性能优异。
3.
The heat-resistance properties of different thermosetting resin cured systems were measured by heat distortion temperature method(HDT),differential scanning calorimetry(DSC) and dynamic mechanical analysis(DMA).
运用热变形温度(HDT)、示差扫描量热(DSC)和动态热机械分析(DMA)方法对不同热固性树脂固化体系的耐热性能进行了测试,并分析了测试结果差异与其物理机制的关系。
补充资料：铂电阻温度表(见电阻温度表)
铂电阻温度表(见电阻温度表)
表。bod旧nZu wendubiao铂电阻温度表见电阻温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条