2) aluminium wire bar
拉丝铝锭;铝线锭;甲基铝
3) aluminum ingot
铝锭
1.
Introduction and analysis on drafit of International standard of aluminum ingot;
铝锭国际标准草案介绍与分析
2.
Realization of Fuzzy Control System Based on PLC for Aluminum Ingot Casting Machine;
铝锭铸造机模糊控制系统在PLC中的实现
3.
And also a method for the determination of micro amount of Al_2O_3 in aluminum ingot samples by spectrophotometry with aluminon as chromatogenic agent has been developed.
用金属铝与液态溴发生反应生成的AlBr3溶于甲醇、而Al2O3在无水条件下不与液态溴发生反应的不同化学行为特性,实现了Al与Al2O3的分离,采用铝试剂光度法测定铝锭中的微量Al2O3。
4) aluminium ingot
铝锭
1.
Determination of Si,Fe,Ga,Cu and Mg in Exported Aluminium Ingot by SOLIS-500 Solids Sampling System;
激光烧蚀固体进样法测定出口铝锭中硅、铁、镓、铜和镁
2.
Simultaneous Determination of 8 Impurity Elements in Aluminium Ingot by ICP-AES;
ICP-AES测定铝锭中八种杂质元素
3.
Development of new automatic stacker of aluminium ingots LDJ-20;
LDJ-20新型全自动铝锭堆垛机的研制
5) aluminum ingots
铝锭
1.
Analysis of influencing factors on aluminum ingots surface quality and its improvement measures
影响铝锭表面质量的因素分析和改善措施
2.
The bar-code technologic scheme is proposed in this paper about the management of Aluminum ingots for remelting in the production of Aluminum smelter, including product check-up, identifier, measurement, putting Aluminim ingots in the storage, arrangement of the materials in stock, taking out/loading and other problem in the technologic process.
文章针对铝冶炼企业的主要产品重熔用铝锭在成品检查、标识、计量、入库、库存实物摆放、出库装车等工艺环节所存在的问题,提出了采用条码技术的解决方案,并对软件实现作了详细论述。
3.
The production process and control system of 20kg aluminum ingots continues casting machine are described,and the production technology figure,control system diagram are derived in this paper.
文章叙述了20kg铝锭连续铸造机的生产工艺过程及控制系统组成,并给出了相应的生产工艺图、控制系统硬件框图,根据生产工艺要求以及控制功能,设计并编制了铝锭连续铸造机生产过程控制软件。
补充资料：拉丝
分子式：
CAS号：
性质：(一)胶黏剂在配制后因超过活性期，胶液部分凝聚所产生的在拉伸情况下成为丝状物的现象。(二)涂料在喷涂时雾化不好，致使涂料不能化为微细的雾滴而呈丝状喷出，所得的涂膜不能流平，出现了拉丝。原因是涂料施工黏度高，稀释剂溶解力差。宜选用适合的溶剂，调整到适宜施工黏度，使涂料在喷涂时能充分雾化，能流平，即可避免此弊病。
CAS号：
性质：(一)胶黏剂在配制后因超过活性期，胶液部分凝聚所产生的在拉伸情况下成为丝状物的现象。(二)涂料在喷涂时雾化不好，致使涂料不能化为微细的雾滴而呈丝状喷出，所得的涂膜不能流平，出现了拉丝。原因是涂料施工黏度高，稀释剂溶解力差。宜选用适合的溶剂，调整到适宜施工黏度，使涂料在喷涂时能充分雾化，能流平，即可避免此弊病。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条