1) crusher drive shaft bearing casing
轧碎机主动轴承盖
2) crusher shaft bearing casing
轧碎机轴承罩
3) Loose main bearing cap.
主轴承盖松动。
4) mill roller bearing
轧机滚动轴承
1.
So it is rather difficult and complex to analyze load peculiarities of mill roller bearing directly.
对于板单元的弹性变形 ,用 Hertz接触公式 ,将其变形以等效间隙代入总体矩阵方程中 ,从而获得轧机滚动轴承负荷特性的三维分布。
5) main bearing cap
主轴承盖
1.
Development of a main bearing cap for an inline 6 cylinder engine;
一种直列式6缸发动机主轴承盖的开发
2.
Problems of falling chip, tool tipping and big noise are happened during cutting off main bearing caps made of gray casting by using combination milling cutters.
采用组合铣刀切断灰口铸铁材质的汽车发动机主轴承盖时 ,出现工件掉渣、刀具崩刃、噪声大等问题。
3.
The characteristic analysis of the suspended main bearing cap of SL4105 diesel engine was presented by using the 3D solid modeling,3D mesh generation,external loads & boundary condition and 3D finite element analysis.
介绍一种运用三维实体造型、三维网格划分、载荷和约束处理及三维有限元分析的方法,对SL4105柴油机悬挂式主轴承盖进行了强度和刚度分
6) rolling mill bearing
轧机轴承
1.
The deflection angle of tapered roller bearings is one of the most important parameters in design and application of rolling mill bearings.
针对轧机轴承的偏斜角在其设计及应用中的重要性,以单列圆锥滚子轴承在额定动载荷作用下、偏斜角为2′时求得的接触应力和接触变形为已知条件,应用Hertz理论,提出求解轧机用重型四列圆锥滚子轴承偏斜角的方法,为轧机轴承的设计提供了理论依据。
2.
Elastohydrodynamic lubrication(EHL) theory was applied to investigate the effect of inner lubrication behavior on service-life of the rolling mill bearings under heavy load,and the approaches to increase service-life via improving lubrication capacity were analyzed with oil film parameter theory and correction life theory.
采用弹性流体动力润滑理论分析了润滑对重载轧机轴承使用寿命的影响,并用油膜参数理论和修正寿命理论研究了改善润滑、提高使用寿命的途径。
3.
The process and properties of 77752 rolling mill bearing made by 100CrMo7 steel bainite hardening were introduced.
介绍了 1 0 0 Cr Mo7钢制 77752轧机轴承的贝氏体淬火处理工艺及其性能 ;用 1 0 0 Cr Mo7钢制轧机轴承进行贝氏体淬火代替 G2 0 Cr2 Ni4A钢制轧机轴承渗碳淬火 ,具有良好的经济技术效益。
补充资料：主轴
1.机械工程中，指从发动机或电动机接受动力并将它传给其它机件的轴。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条