1) front bearing retainer
前轴承盖
2) front main bearing cap
前主轴承盖
3) front left main bearing cap bolt
前左主轴承盖螺栓
4) bearing cap
轴承盖
1.
In the paper, the 3D design process of the bearing cap progressive die was mainly described based on Solid Edge V17.
主要叙述了基于Solid Edge V17平台实现轴承盖级进模三维设计的过程。
2.
Through the retrofit of large and middle scale motor shaft-extensio n end bearing cap,XinYu power plant divides shaft-extension end bearing cap of mo tor with bearing stand into upper and lower parts.
新余发电有限责任公司通过对大、中型(滚动轴承)电动机轴伸端轴承盖进行改造,将有轴承座的电机的轴伸端的轴承盖分上、下两部分剖开的改造工艺可方便轴承盖的拆装,在电机运行异常时,便于及时检修,可以大大减少电动机设备的损坏事故。
3.
Production cost is vital to an enterprise ,how to control production cost is the most important,the paper introduces the optimal design of the mold of bearing cap for roto
生产成本对企业至关重要,如何控制生产成本成为企业头等大事,本文重点介绍了海马汽车中一个叫转子轴承盖模具的最优化设计。
5) main bearing cap
主轴承盖
1.
Development of a main bearing cap for an inline 6 cylinder engine;
一种直列式6缸发动机主轴承盖的开发
2.
Problems of falling chip, tool tipping and big noise are happened during cutting off main bearing caps made of gray casting by using combination milling cutters.
采用组合铣刀切断灰口铸铁材质的汽车发动机主轴承盖时 ,出现工件掉渣、刀具崩刃、噪声大等问题。
3.
The characteristic analysis of the suspended main bearing cap of SL4105 diesel engine was presented by using the 3D solid modeling,3D mesh generation,external loads & boundary condition and 3D finite element analysis.
介绍一种运用三维实体造型、三维网格划分、载荷和约束处理及三维有限元分析的方法,对SL4105柴油机悬挂式主轴承盖进行了强度和刚度分
6) bearing cover
轴承盖
1.
Introduced the design of better bearing cover casting to stamping, analyzed its point of stamping craft course and mold design under batch production to the point, and expounded the merit, feasibility, economy etc.
介绍了轴承盖的改进设计，分析了批量生产条件下其冲压工艺过程及模具设计要点，并阐述了铸件改冲压件的优点、可行性、经济性等。
补充资料：盖天盖地
【盖天盖地】
（杂语）覆盖天地也。又曰普天普地。示自己意气满溢，磅礴于宇宙之意。宗门统要续集十六岩头全斋条所谓：“师云：若欲播扬大教，一一从自己胸襟流出将来，为我盖天盖地去”之类是也。
（杂语）覆盖天地也。又曰普天普地。示自己意气满溢，磅礴于宇宙之意。宗门统要续集十六岩头全斋条所谓：“师云：若欲播扬大教，一一从自己胸襟流出将来，为我盖天盖地去”之类是也。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条