1) high reducibility sinter
高还原性烧结矿
2) pre-reduced sinter
预还原烧结矿
1.
In this article,the mineral composition and microstructure of pre-reduced sinter from Hainan iron ore under different technical conditions are studied,including forming mechanism of mineral composition and their influence on the characteristics of pre- reduced sinter.
研究了不同工艺条件下海南矿粉预还原烧结矿的矿物组成、含量和显微结构,阐明了预还原烧结矿的形成机理,及矿物组成对其性能的影响。
3) reductive sintering
还原烧结
1.
On the basis of domestic and international literatures on comprehensive extraction of Al and Fe,"reductive sintering-leaching-magnetic separation" process was developed for comprehensively extracting Al and Fe,and studied in detail.
在查阅了大量的国内外综合提取铝铁资料的基础上,选取“还原烧结-溶出-磁选”工艺作为综合提取铁铝的方案,并对此进行了细致地研究。
5) high-alumina sinter
高铝烧结矿
1.
In allusion to high-alumina sinter that high rate of pulverization and impact for blast furnace permeability and performance of slag and so on,rationality of sinter with V-Ti pellets was analyzed by experiments of mechanical strength and metallurgical properties of sinters and V-Ti pellets.
针对高铝烧结矿粉化率高,影响高炉透气性和炉渣性能等特点,通过对烧结矿和钒钛球团矿进行机械强度和冶金性能实验,分析其与钒钛球团矿搭配的合理性。
6) selective reduction roasting
选择性还原焙烧
1.
The process of selective reduction roasting-ammonia leaching-solvent extraction-electrowinning is adopted to extract nickel,cobalt and recover iron from low grade nickeliferous laterite ore.
本研究采用选择性还原焙烧-氨浸-溶剂萃取-电积工艺从低品位红土镍矿中综合提取镍、钴、铁,重点介绍了采用煤作还原剂,选择性还原焙烧的试验研究。
补充资料：聚四氟乙烯预烧结树脂
分子式：
CAS号：
性质：由悬浮聚四氟乙烯树脂经加压、高温烧结和粉碎等处理而得到的白色颗粒状的聚四氟乙烯树脂。具有聚四氟乙烯的各种优异性能。因系通过预烧结处理，故具有良好的流动性，表观密度大[(600±100)g/L]，适用于挤出压力高(一般10～20MPa)的柱塞挤出成型。用预烧结树脂可制得直径5～40mm的棒材和壁厚3～25mm的管材。
CAS号：
性质：由悬浮聚四氟乙烯树脂经加压、高温烧结和粉碎等处理而得到的白色颗粒状的聚四氟乙烯树脂。具有聚四氟乙烯的各种优异性能。因系通过预烧结处理，故具有良好的流动性，表观密度大[(600±100)g/L]，适用于挤出压力高(一般10～20MPa)的柱塞挤出成型。用预烧结树脂可制得直径5～40mm的棒材和壁厚3～25mm的管材。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条