1) multiple arc
多重弧
2) multi-arc
多弧
1.
TiN and (Ti,Cr)N composite films were deposited on high speed steel by AIP-01 multi-arc ion plating.
利用AIP 01型多弧离子镀膜机在高速钢基体上制备了TiN及(Ti,Cr)N复合薄膜, 对制得的薄膜进行盐水全浸泡试验, 研究了带有宏观熔滴颗粒的TiN及(Ti,Cr)N复合薄膜的腐蚀机理。
3) argon arc remelting
氩弧重熔
1.
Influence of argon arc remelting process on microstructure and properties of coating prepared by hot dipping aluminizing on surface Q235 steel
氩弧重熔对Q235钢热浸镀铝层组织和性能的影响
2.
The microstructure,wear resisting and abrasive mechanism of argon arc remelting area of alloyed casting iron camshaft is studied.
研究了合金铸铁凸轮轴氩弧重熔淬火后强化层的组织、耐磨性及磨损机理。
3.
This paper studied the causes of the early stage pitting on local areas and peeling off after 5000km drive in some grey cast iron camshafts which were treated by argon arc remelting.
分析研究了灰铸铁凸轮轴经氩弧重熔工艺处理后，约５０００ｋｍ 正常行驶后个别轴局部区域出现早期麻点与部分剥落而失效，结果证明早期失效的原因为氩弧重熔工艺不稳定所致。
4) arc restriking
电弧重燃
1.
The reason of arc restriking overvoltage is analyzed in view of the restriking condition when the 35kV vacuum circuit breaker breaks the reactive compensation device.
针对35kV真空断路器开断无功补偿装置时发生重燃的实际情况,分析了其电弧重燃产生过电压的机理。
5) Arc remelting
电弧重熔
1.
Arc remelting is an advanced processing to increase properties of contact material for vacuum switches,and the properties of contact are determined by arc contact material interaction in the process of arc remelting.
电弧重熔法是提高真空开关触头材料性能的一种先进工艺方法 ,触头材料的性质决定于电弧与触头材料间的作
6) double island arc
双重岛弧
补充资料：多苯基多亚甲基多异氰酸酯
多苯基多亚甲基多异氰酸酯，简称PAPI，或称粗MDI，浅黄色至褐色粘稠液体．有刺激性气味。相对密度(20℃／20 ℃)1．2，燃点218℃。PAPI实际上是由50％MDI与50％官能度大于2以上的多异氰酸酯组成的混合物。升温时能发生自聚作用。溶于氯苯、邻二氯苯、甲苯等。PAPI的活性低，蒸气压低，只是TDI的百分之一，故毒性很低。
用于制造聚氨脂胶粘剂。也可直接加入橡胶胶粘剂中，改善橡胶与尼龙或聚酯线的粘接性能。贮存于阴凉、通风、干燥的库房内，远离火种、热源。严格防水、防潮，避免光照。
用于制造聚氨脂胶粘剂。也可直接加入橡胶胶粘剂中，改善橡胶与尼龙或聚酯线的粘接性能。贮存于阴凉、通风、干燥的库房内，远离火种、热源。严格防水、防潮，避免光照。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条