1) condensing rate
冷凝速度
2) solidified velocity
凝固冷却速度
1.
At different solidified velocity, the change of microstructure and performance on magnesium alloy anode has been studied.
论文研究了不同凝固冷却速度下,镁合金阳极显微组织和性能的变化。
3) rapid solidification
快速冷凝
1.
This paper has analyzed the reasons of the brittleness of rapid solidification Al-Li alloys and introduced some main toughening methods in manufacturing,forming and heat treatment of the alloys.
通过对快速冷凝 (RS)Al-Li合金低塑韧性原因的分析 ,介绍了Al-Li合金制备、成材、热处理等过程中一些主要韧化途径 ,并简单讨论了获得较好综合性能的Al-Li合金制品的工艺方法及大致工艺参数范
2.
The microstructure and effect of grain refining of Al-Ti-B interalloy rods prepared by the process of rapid solidification-extrasion have been investigated by means of X-ray diffrac-tion，SEM and optical microscope in this paper.
借助Ｘ射线衍射、扫描电镜、金相显微技术等手段，对采用快速冷凝喷粉或离心制粒－挤压法制得的Ａｌ－Ｔｉ－Ｂ中间合金线杆的组织结构和其晶粒细化效果进行了研究。
3.
By means of rapid solidification,Al-Cu-Fe-Zn alloy powders were produced.
本文通过快速冷凝方法制得了Al-Cu-Fe-Zn系合金粉末。
4) condensing rate
冷凝速率
5) condensation temperature
冷凝温度
1.
The condensation temperature and evaporation temperature are variational in condensator and evaporator using R22/R142b non-azeotropic mixture refrigerant.
R2 2 /R14 2b非共沸混合制冷剂在冷凝器和蒸发器中其冷凝温度和蒸发温度是变化的。
2.
Through a theoretical analysis the authors have derived a relationship for calculating the mean condensation temperature of a multi-pressure condenser, which has taken into account the variation of heat transfer factor with the change of condenser construction scheme and cooling water inlet temperature.
通过理论分析 ,得出考虑传热系数随凝汽器结构和冷却水入口温度变化条件下多背压凝汽器的平均冷凝温度的关系式 ,分析了各级传热面积和循环倍率对平均冷凝温度的影响 ,并以多背压凝汽器的平均冷凝温度为目标函数 ,得出多背压凝汽器的最优结
3.
,air wet-bulb temperature,condensation temperature and relative moisture were conducted.
对影响板式蒸发式冷凝器热工性能的主要因素——空气的湿球温度、冷凝温度、相对湿度做了实验研究。
6) condensing temperature
冷凝温度
1.
Discussion of the condensing temperature in the standard of SCREW REFRIGERANT COMPRESSORS;
《螺杆式制冷剂压缩机》标准中冷凝温度的探讨
2.
Some researches in an ice harvester machine are made which indicate that the evaporating temperature is the most significant factor which influence the COP (Coefficient of Performance) of a refrigeration compressor while both the evaporating temperature and the condensing temperature are two main factors.
通过对某冰片滑落式冰蓄冷空调系统运行的分析及研究,表明在影响制冷机COP值的两大因素——蒸发温度和冷凝温度中,蒸发温度占主导地位,要提高制冷机运行的COP值应当首先考虑提高制冷机的蒸发温度。
3.
By use of such refrigerants,the compressor discharging temperature is almost equal to the condensing temperature,and problems relative to high compressor discharging temperature are avoided.
可使工质在压缩过程中始终接近饱和蒸气状态,压缩机排气温度约等于工质的冷凝温度,从而可较好地解决排气温度过热所引起的一系列问题。
补充资料：迟延凝固剂
分子式：
CAS号：
性质：又称胶凝剂。加入胶乳中，能使胶乳从液态转变为均匀的半刚性固体凝胶，而且保持原有形状及大小的物质。迟延凝固剂常用的有硅氟化钠，碱性的钛、锆与硼的氟化物等。多用于胶乳泡沫制品的加工，以氟硅酸盐(如氟硅酸钠、氟硅酸钾)的应用最为普遍。
CAS号：
性质：又称胶凝剂。加入胶乳中，能使胶乳从液态转变为均匀的半刚性固体凝胶，而且保持原有形状及大小的物质。迟延凝固剂常用的有硅氟化钠，碱性的钛、锆与硼的氟化物等。多用于胶乳泡沫制品的加工，以氟硅酸盐(如氟硅酸钠、氟硅酸钾)的应用最为普遍。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条