1) solidification rate
凝固速度
1.
Influence of solidification rate on solid-liquid interface in unidirectional solidification microstructure of austenitic stainless steel
凝固速度对奥氏体不锈钢定向凝固组织及其固液界面稳定性的影响
2.
The percentage of RE in the matrix increases with the increase of solidification rate; the carbides in directional solidification microstructure are refined by RE added in high chromium cast iro.
研究表明,稀土主要位于高铬铸铁的基体组织中,随凝固速度的增加,稀土在基体中的含量增加;稀土对高铬铸铁定向凝固组织中的碳化物具有细化作用,并随凝固速度的增加,定向凝固高铬铸铁组织细化程度提高,同时稀土的加入使高铬铸铁的抗拉强度明显提高。
3.
The microstructure and its evolution of directionally solidified Cu-Cr alloy were investigated under the condition of different solidification rates,by use of optical microscope and SEM.
在高梯度定向凝固装置上制备Cu-1·0%Cr(质量分数)合金,用金相显微镜、扫描电镜进行微观组织的观察,研究定向凝固速度对Cu-Cr合金微观组织形貌的影响。
2) solidified velocity
凝固冷却速度
1.
At different solidified velocity, the change of microstructure and performance on magnesium alloy anode has been studied.
论文研究了不同凝固冷却速度下,镁合金阳极显微组织和性能的变化。
3) rapid solidification
快速凝固
1.
Rapid Solidification of Cu-10Ag Alloy Droplets by Ultrasonic Arc Spray Atomization;
超音速电弧喷射雾化Cu-10Ag合金熔滴的快速凝固
2.
Carbide and its stability in FGH95 superalloy powders during rapid solidification;
快速凝固FGH95合金粉末中的碳化物及其稳定性
3.
Microstructure evolution of hypereutectic Al-Si alloy during rapid solidification;
过共晶Al-Si合金快速凝固组织演变
4) rapidly solidification
快速凝固
1.
Microstructure and property of Mg_(80)Cu_(15)Y_5 alloy by rapidly solidification and hot extrusion
热挤压快速凝固Mg_(80)Cu_(15)Y_5合金棒材的组织与性能
2.
The effects of rapidly solidification on the microstructure and the corrosion behavior of Mg-5Zn-1Y-0.
研究了快速凝固Mg-5Zn-1Y-0。
5) solidification rate
凝固速率
1.
The empirical results indicate that the increase of solidification rate can achieve intermetallic particles reinforced phase with ideal morphological features in Al-Ni alloy.
实验结果表明,提高凝固速率可以使Al-Ni合金获得理想形貌的金属间化合物强化相。
2.
Exporimental results show that the stress- rupture life of DZ22 at 980℃ and 220 MPa was increased from 71 hours and 50 nunutes to 168 hours and 5 minutes at relatively high solidification rate.
本文采用ZMLMC超高梯度定向凝固法(ZMLMC法),研究了两种凝固速率下DZ22合金的高温力学性能和组织。
3.
The dendritic arm spacings and microsegregations of directionally solidified superalloy DZ22 at various solidification rates have been studied with the help of a ZMLMC directional solidification equipment.
采用新研制的超高梯度定向凝固装置,研究了不同凝固速率下定向凝固高温合金DZ22的枝晶臂间距和枝晶偏析。
6) melt spinning
快速凝固
1.
3~1) are prepared by means of vacuum arc melting followed by high temperature annealing and quenching or melt spinning method.
0)在常规熔铸、高温退火+淬火及快速凝固不同制备条件下的组织结构和电化学性能。
2.
4 were prepared using conventional cast, rapid solidification (melt spinning) and annealing processes.
4 在常规熔铸、快速凝固、退火处理不同制备条件下的组织结构和电化学性能。
补充资料:迟延凝固剂
分子式:
CAS号:
性质:又称胶凝剂。加入胶乳中,能使胶乳从液态转变为均匀的半刚性固体凝胶,而且保持原有形状及大小的物质。迟延凝固剂常用的有硅氟化钠,碱性的钛、锆与硼的氟化物等。多用于胶乳泡沫制品的加工,以氟硅酸盐(如氟硅酸钠、氟硅酸钾)的应用最为普遍。
CAS号:
性质:又称胶凝剂。加入胶乳中,能使胶乳从液态转变为均匀的半刚性固体凝胶,而且保持原有形状及大小的物质。迟延凝固剂常用的有硅氟化钠,碱性的钛、锆与硼的氟化物等。多用于胶乳泡沫制品的加工,以氟硅酸盐(如氟硅酸钠、氟硅酸钾)的应用最为普遍。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条