1) pre-sintered density
预烧密度
2) sintered density
烧结密度
1.
Effects of process parameters on the gelcasting green strength and sintered density of stainless steel;
工艺参数对凝胶注模成型不锈钢坯体强度和烧结密度的影响
2.
The influence of Cr on sintered density, microstructure and wear resistance of FeNiMo system prealloyed powders were investigated.
研究了铬对Fe-Ni-Mo系粉末烧结密度、微观组织特征及耐磨性能的影响,通过SEM观察分析了磨损形貌,探讨了其摩擦磨损机制。
3.
It is found that the green density and sintered density of YBa_2Cu_3O_(7-δ) powders with different granularity varied differently with the variation of pressure.
结果表明,不同粒度YBaCuO超导粉体的压坯密度、烧结密度(即烧结前后的致密度)随压力的变化规律不同。
3) sintering density
烧结密度
1.
IN AFS-320MZ/Q,with PS as the testing material, the influence of laser power,scanning speed and scanning space on sintering density is analyzed by single factor analysis.
以聚苯乙烯为试验材料,在AFS-320MZ Q自动成型机上,采用单因素分析法,分别研究了激光功率、激光束扫描速度、扫描间距等3个烧结成型工艺参数对烧结密度的影响关系,得出要保证烧结质量与加工效率,需合理匹配成型工艺参数。
4) calcining temperature
预烧温度
1.
The effect of calcining temperature on the microstructure and magnetic properties of high permeability MnZn ferrites;
预烧温度对高导磁率MnZn铁氧体微结构和磁性能的影响
2.
The calcining temperature was in the range from 950 ℃ to 1100℃.
对CCTO陶瓷进行物相分析,并测试了20Hz-1MHz频率范围和25～150℃温度区间的介电性能和阻抗谱,详细研究了预烧温度对CCTO陶瓷烧结性能、晶体结构和介电性能的影响。
3.
The effects of calcining temperature on sintering,microstructure and electromagnetic properties of NiCuZn ferrites for multilayer chip inductor(MLCI) are investigated.
研究了预烧温度对多层片式电感器用NiCuZn铁氧体的烧结、显微结构和电磁性能的影响。
5) pre-sintering temperature
预烧温度
1.
Research on pre-sintering temperature of BaO-Y_2O_3-5TiO_2 system microwave dielectric ceramic;
BaO-Y_2O_3-5TiO_2系微波介质陶瓷预烧温度研究
2.
The influence of pre-sintering temperature on the microstructure and properties of nano-composite Ti(C,N)-based eermets has been studied using SEM,TEM and EDX.
用真空预烧+热等静压处理工艺制备了纳米复合Ti(C,N)基金属陶瓷,用SEM和TEM／EDX研究了预烧温度对纳米复合Ti(C,N)基金属陶瓷显微组织和性能的影响。
3.
X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to investigate the influence of pre-sintering temperature on the pre-sintered phases and microstructure of sintered Mn-Zn ferrite.
用X射线衍射(XRD)仪和扫描电子显微镜(SEM)研究了预烧温度对铁氧体预烧相及烧结显微结构的影响。
6) calcined temperature
预烧温度
1.
Research on the calcined temperature of ceramics based on (1-x)NBT-xBaTiO_3 during the preparation;
(1-x)NBT-xBaTiO_3系陶瓷材料制备过程中预烧温度的研究
2.
The effect of salt quantities and calcined temperature on microstructure and morphology of Bi_4Ti_3O_~12 powder was investigated.
研究了预烧温度及熔盐含量对粉体形貌及显微结构的影响。
补充资料：预烧
分子式：
CAS号：
性质：在制成耐火制品前，预先对原料进行热处理的工艺。原料在预烧时将产生一系列的物理化学反应，作为坯料能改善制品的成分及其组织结构，保证制品的体积稳定及其外形尺寸的准确性，提高制品的性能。预烧依材质和使用要求而异，可以分为活化烧结、轻烧、死烧和二步煅烧等。
CAS号：
性质：在制成耐火制品前，预先对原料进行热处理的工艺。原料在预烧时将产生一系列的物理化学反应，作为坯料能改善制品的成分及其组织结构，保证制品的体积稳定及其外形尺寸的准确性，提高制品的性能。预烧依材质和使用要求而异，可以分为活化烧结、轻烧、死烧和二步煅烧等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条