2) axial pressure
推轴推力
3) axial thrust
轴向推力
1.
Influence of friction coefficient on vibration characteristic of rub-impact rotor with axial thrust;
摩擦系数对轴向推力作用下碰摩转子振动特性的影响
2.
The paper in addition reports on systematic studies of the axial thrust calculation of turbine stages and the derivation of a new formula, accompanied by a detailed calculation of typical turbine stage.
对汽轮机级轴向推力计算进行了系统的研究并推导出新的公式,针对典型机组的级进行了详细计算。
3.
This paper presents a new method for measuring and testing of axial thrust for vertical canned motor pumps.
介绍测试立式屏蔽电泵轴向推力的一种新方法，其测试精度较高，并经过了实际产品验证，对实际操作具有指导意义。
4) thrust bearing
推力轴承
1.
Oil lift system of thrust bearing of generating unit in Three Gorges;
三峡机组推力轴承高压油顶起系统
2.
The Reason and Solution to the Oil Flinging and Infiltrating of Generator Thrust Bearing;
发电机推力轴承甩、渗油原因及处理
3.
The methods for measurement of lubricant film Thickness of thrust bearing;
推力轴承油膜厚度测量方法概述
5) thrust bearings
推力轴承
1.
The PNF method for investigating the bifurcation of the periodic solution of the system is used to study the thermal stability of thrust bearings.
建立了考虑瞬态油膜压力影响的热稳定性分析模型 ,用求解系统周期解分岔的 PNF法对推力轴承系统的热稳定性进行了研究 ,结合 Poincare映射与胞映射法思想 ,提出了用于分析系统周期稳态解全局特性的数值计算 PCM方法 ,并对推力轴承热系统周期稳态解的全局特性进行了考
2.
It was theoretically proven that thermal instability exists during operations for thrust bearings based on an infinitely wide thrust bearing.
以简化推力轴承为对象 ,理论上证明了推力轴承运行时存在热不稳定性 ,采用小扰动分析法得到了油膜温度的扰动方程 ,应用简正模态分析法推导了无量纲热不稳定性准则数以及推力轴承运行的热不稳定性准则 。
3.
The three dimensional modeling for sector shaped tilting pad thrust bearings with polytetrafluoroethylene plastic pads and a numerical simulation with finite element method are presented.
通过建立水电机组分块可倾瓦推力轴承热弹流动力润滑数值模型 ,利用有限元法联立求解三维控制方程组 ,给出了准确的推力轴承润滑分析方法 。
6) axial force
轴向推力
1.
Taking the air conditioning water system of a high-rise building as an example, analyses the axial force resulting from ripple compensators on main vertical pipes and its characteristics during operation and pressure test.
以一高层建筑空调水系统为例,分析了水系统总立管上波纹补偿器在运行和水压试验状况下所产生的轴向推力及其特点,提出减小轴向推力的措施;并分析了水泵进出口管道上橡胶柔性软接头的安装位置对管道和水泵的影响,认为橡胶柔性软接头安装在水泵进出口横管上比安装在立管上好。
2.
The axial force and power consumption are important factors of affecting reliability of twin screw pulping ex-truder,at present there are no theory calculation methods about them.
轴向推力和功耗是影响双螺杆磨浆机可靠性的重要因素,目前尚无理论计算方法。
补充资料：DNA分子花窗(沿B―DNA轴线方向看)
[图]
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条