1)  acoustic mode,acoustical mode
声模
2)  sound absorption model
吸声模型
1.
According to the characters of porous metals,a new effective bulk modulus formula with simpler expression was obtained by considering the heat exchange between the metallic skeleton and air in pore on the basis of phenomenological Biot-Allard model,therefore an extended sound absorption model was put forward.
根据金属骨架多孔材料的特点,在Biot-Allard刚性骨架多孔材料内流吸声模型的基础上,考虑金属的热导特性,推导出一种新的、形式较简单的有效体积模量表达式,从而得到了一种扩展的吸声模型。
3)  sound-generating model
发声模型
1.
The sound-generating models for the main sources of tire/road noise were established based on analysis of the sound generating mechanisms of tire/road noise, and the total time-domain wave was obtained by combining the noise waves of the tire and road.
在分析轮胎/道路噪声发声机理的基础上,建立了轮胎/道路噪声各主要噪声源的发声模型,并将轮胎和道路的噪声波合成得到总的时域波形,通过离散傅立叶变换得到轮胎/道路噪声的频谱,得出了时域耦合因子行阵和频域耦合因子行阵,为低噪声轮胎花纹和低噪声路面的研究和设计提供了理论依据和技术路线。
2.
Based on the sound-generating charateristics of smooth tread,ribbed patterns and block patterns of tires,the original sound-generating model was revised,a physical model suitable for sound-generating test of tire with non-small block patterns was proposed,the relative programmes BPTNS and BPODS were worked out,and the accuracy of the model was confirmed by the simulation test.
根据光面轮胎、条状花纹和大块状花纹的发声特点,对原来的发声模型进行修正,提出了适用于非小块状花纹的发声试验物理模型,并编制相关程序BPTNS和BPODS,仿真试验验证了模型的准确性。
4)  acoustic mode
声模态
1.
Acoustic modes of the combustion chamber were calculated with FEM software ANSYS when the length and number of baffles change,and the influences of the changes on the acoustic modes are compared.
利用ANSYS软件数值计算了隔板长度变化以及隔板数目变化时,对应的燃烧室声模态,并比较了它们的变化对燃烧室声模态造成的影响。
2.
Analysis is done to compare the results of acoustic model analysis with the excitation frequency characteristics of both inside and outside of the car,which provides the evidence for the cab noise prediction and the acoustic characteristic i.
采用Hypermesh软件建立了某车型的室内声场有限元模型,用SYSNOISE软件对该有限元模型进行自由模态分析,得到声场的各阶模态频率和振型,将声模态分析结果与汽车内外部的激励源频率特性进行对比,为改善车内声学特性,对车内噪声预测提供了参考。
5)  ultrasonic simulation
超声模拟
1.
In this paper,ultrasonic simulation method has been applied to study seismic waves affected by Karst zone in limestone of North China coalfield.
应用地震波超声模拟方法,研究了华北型煤田的煤系底部奥灰岩岩溶发育带对地震波的响应特征,为地震勘探技术应用于矿井台水提供了依据。
6)  Ultrasonic moduli
超声模量
参考词条
补充资料:局域声子模


局域声子模
localized phonon modes

局域声子模loealized曲onon modes晶体中存在杂质或缺陷时可能产生的、局限于杂质或缺陷附近的振动,其振幅随与杂质或缺陷的距离增大呈指数衰减。 最简单的例午是在原子质量为M的一维单原子链中,有一个质量为材‘的杂质原子。杂质对整个频谱的影响是很小的,但会出现局域声子模。如果杂质原子的质量轻,即M‘对一‘将会出现共振模,这是一种准局域的振动。实际上,这时与杂质原子相联系的振动频率落在频带之中,这种频率的振动模虽不是局域的,但是在杂质附近表现的特别强。 如果晶体元胞中有多于一个原子,格波振动不仅有声学支,还有光学支,它们分别形成频带,在频带之间可能有带隙,或者称为频隙,这时晶体中的杂质或缺陷可能引入新的局域声子模,其频率落在频隙之中,称为隙模。 在实际晶体中,局域的或准局域的振动模都曾有多方面的证实,这些局域振动的频率在红外光的频率范围,存在有红外吸收。近年来红外技术的研究有了很大发展,例如硅中的翻形成高颧模,氮替代GaP中的磷出现高频模,氯替代Kl中的碘产生的隙模,KCI中的银形成的共振模等。 晶体的表面或界面出现另一种形式的局域振动。它是一种局限在表面附近的格波,这种格波的传播方向沿着表面,其振幅随着与垂直表面距离的增加而指数下降。晶格表面的重构现象,表面的原子吸附,都会影响表面局域振动,因而表面声子模的研究是表面物理的重要研究方面之一。(韩汝琦)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。