1) churing loss
搅动损失
2) churning loss
搅油损失
1.
In this paper,the influence of the immersion depth on the churning loss of a practical spur gear used in the high speed train is studied by using experiential equations at different train speeds.
本文针对中国南车集团开发的高速列车传动齿轮箱,采用经验公式,计算分析了在不同转速下,齿轮箱浸油深度对搅油损失的影响。
3) dynamic loss
动态损失
1.
Bayes prediction modeling for dynamic loss of manufacturing accuracy;
加工装置的精度动态损失贝叶斯建模预报
2.
Study on the model of dynamic loss of manufacturing accuracy;
机械加工精度动态损失模型的研究
4) kinetic energy loss
动能损失
1.
By using nonlinear finite element analysis code ANSYS/DYNA to build a dynamic analysis model of the round-link,the paper analyzes the kinetic energy loss of the round-link chain under the different initial conditions and the energy absorption under chain blocked,according to the dynamic process of the round-link chain under chain blocked condition.
同时,对不同初始条件下的圆环链动能损失以及卡链过程中圆环链的能量吸收特性进行了分析。
2.
By using nonlinear finite element analysis code ANSYS/DYNA,build a dynamic analysis model of the round-link,analyzes the kinetic energy loss of the round-link chain under the different initial condition and the energy absorption under chain blocked,according to the dynamic process of the round-link chain under chain blocked condition.
同时,对不同初始条件下的圆环链动能损失以及制动过程中链环的能量吸收特性进行了分析。
5) flow loss
流动损失
1.
Analysis of flow loss induced by inlet total pressure distortion in a small fan;
某小型风扇内进口总压畸变引起流动损失分析
2.
In this paper,the designing method of the fasting cooling system of furnace is introduced in detail by demonstrating how to calculate flow loss,select turbine and design transfer.
通过阐述风机的选型计算,系统流动损失计算和换热器的设计计算,详细地介绍了炉膛充氩加热炉速冷系统的设计方法。
3.
The results show that the flow loss is reduced with the increasing of the coolant mass when the injection angle is 30°at the instant of injection from single row of holes.
采用数值求解雷诺平均N-S方程的方法,数值模拟了带冷气掺混的涡轮内部全三维黏性流场,研究了冷气掺混对涡轮流动损失和气动性能的影响。
6) rolling energy loss
滚动损失
1.
The results showed that a new tire tread material with good overall properties, especially low rolling energy loss and good wet grip was obtained when the styrene content was 20%￣23%,vinyl content was about 45%,and molecular weight of one arm was 80000.
该材料的滚动损失低，抗湿滑性能好。
补充资料：搅动流动法
分子式：
CAS号：
性质：装置原理图见“流动法”。设反应液流入(出)速度为u，反应器体积为V，由于高速搅动，反应液在反应器内的浓度是均匀的，平均停留时间V/u亦即反应时间。若入口、出口浓度分别为[A]0、[A]，则一级反应可得k=(u/V){([A]0-[A])/[A]}，也可求得其他复杂反应的动力学公式。优点是(土)避免了积分，(2)可在恒定溶剂条件下进行反应，(3)有充足的时间进行反应中间物浓度测定。缺点是只能测量较慢的反应的动力学参数，且消耗大量溶液。每次只能测量速率方程中的一组数据。
CAS号：
性质：装置原理图见“流动法”。设反应液流入(出)速度为u，反应器体积为V，由于高速搅动，反应液在反应器内的浓度是均匀的，平均停留时间V/u亦即反应时间。若入口、出口浓度分别为[A]0、[A]，则一级反应可得k=(u/V){([A]0-[A])/[A]}，也可求得其他复杂反应的动力学公式。优点是(土)避免了积分，(2)可在恒定溶剂条件下进行反应，(3)有充足的时间进行反应中间物浓度测定。缺点是只能测量较慢的反应的动力学参数，且消耗大量溶液。每次只能测量速率方程中的一组数据。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条