1) extrusion defect
挤压缺陷<冶>
2) extrusion defect
挤压缺陷
1.
The extrusion defects of aluminium profiles most have relation with die structure,and recommending several methods of design dies and to overcome defects of aluminium profiles.
铝型材挤压缺陷的产生很大一部分与模具结构有关,简要介绍几种型材模具的优化设计,以克服挤压型材缺陷的产生。
3) pressing defect
压制缺陷<冶>
4) squeeze casting / infiltration defects
挤压铸造/充填缺陷
5) metallurgical defects
冶金缺陷
1.
The results show that residual stress and serious metallurgical defects near the fracture initiation site are the failure cause of the gearbox output shaft.
利用金相检查、SEM分析和X射线衍射物相分析等方法,对材料为42CrMo钢的开裂大型齿轮箱输出轴进行失效分析,结果表明,残余拉应力和位于中心的严重的冶金缺陷是输出轴失效的原因。
2.
The result indicates that the metallurgical defects in the casting is the reason that cause the brittle fracture of the reinforced bars, and the change of the environmental temperature only has the function of catalysis.
对使用过程脆断的30MnSi高强钢筋的断口、金相组织和轧制状态下的母材以及连铸坯低倍组织进行了全面的检验和分析,检验结果表明,连铸过程中的冶金缺陷是诱发钢筋脆断的因素,而环境温度的变化只是起到催化的作用。
3.
Aiming at the current existing problems of study and fabrication of national aluminum sheet used for easy-open can without being pay more attention to the effects of intrinsic metallurgical defects, a new idea to link organically with hot deformation process in the study of the aluminum sheet used for easy-open can has been put forward by author.
针对目前我国铝材生产与研究中对内在冶金缺陷的影响作用重视不足、液态(熔体)处理与各种固态处理均是按各自系统独立进行研究的现状,作者结合本课题组的前期研究基础,以具有实用价值且量大面广的易拉罐用铝材(Al-Mn-Mg合金)作为研究对象,提出从改善铝材冶金质量这一关键技术入手,将铝材的处理状态(熔体处理和均匀化)与热变形加工有机地结合起来进行研究的新思路。
6) metallurgical defect
冶金缺陷
1.
The bolts was fractured after used for two years, resulting from bad working and serious metallurgical defects , such as segregation and inclusion.
结果表明:螺栓在服役2 a后就发生了断裂,主要是因为螺栓加工不良和钢中存在严重的偏析与夹杂物等冶金缺陷;在交变拉应力作用下,使得螺栓在螺纹沟处发生脆性疲劳断裂。
2.
The metallurgical defects,such as high density inclusion and low density inclusion,always appear in the titanium alloys,which are the fatigue crack sources in the titanium components and lower the application life of the components.
钛合金铸锭中经常出现高密度夹杂和低密度夹杂等冶金缺陷,这种夹杂缺陷成为钛合金零部件的疲劳裂纹源,降低零部件的使用寿命,用于航空发动机,可能引起机毁人亡的重大灾难。
3.
The experimetal results show that the premature break of drive gear shaft is attributed to the metallurgical defect in raw 20CrMo steel and abnormal structure present in hardened case as well as lower core hardness.
结果表明,驱动齿轮轴的过早断裂系原材料冶金缺陷、表面硬化层组织反常和心部硬度偏低所致。
补充资料：挤压制品缺陷
挤压制品缺陷
extrusion defects
J iya ZhiPin quexian挤压制品缺陷(extrusion defeets)挤压制品缺陷的种类、产生原因和消除方法如表所列。 挤压制品缺陷、产生原因和消除方法j续表丁 (丁桦)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条