1) electrodecontamination
"电去污,电净化"
2) electricity
电
1.
Introduced reducing basic electrical bill,enhancing power factor,increasing voltage rank,eliminating high energy consumption equipment,rearranged production by using the difference electrovalence with peak,plane and vale,used frequency conversion control,adopted new electricity saving measure and electricity saving technology so on.
介绍了降低基本电费、提高功率因数、提高电压等级、淘汰高能耗设备、利用电价的峰平谷差价安排生产、使用变频控制、采用新型节电技术等节电措施。
2.
It is pointed out:the unity with electrochemical enterprises is necessary for existing of chlorate enterprises, and purchasing electricity with net connecting is the way for them to develop and strengthen.
电是生产氯酸盐的主要原料。
3) electric
电
1.
The anatomic basis and the clinical treatment of the elbow joint stiffness after electric injury;
电烧伤后肘关节纤维性强直的解剖学基础与临床治疗
2.
Mechanism of the role of electrical field in electrical injury;
电场在电损伤中的作用机制
4) electrical
电
1.
Early transplantation of double rectus abdominis musculo-cutaneous flaps from upper abdomen for the repair of patients with electrical injury in the wrist;
早期应用上腹部腹直肌双肌皮辦修复腕部电烧伤创面
2.
Establishment of a rabbit model of non-thermal high voltage electrical injury;
兔高压电非热性损伤模型的建立
3.
Morphological changes in canine heart after electrical injury.;
电烧伤犬心脏组织的形态观察
5) corona discharge
电晕放电
1.
Conductive characteristic of anticorrosion coating for flue gas cleaning equipment by corona discharge;
电晕放电烟气净化设备防腐涂层导电特性研究
2.
Study on ion produce by high-voltage corona discharge;
高压电晕放电产生离子的研究
6) arc discharge
电弧放电
1.
Analysis of low energy arc discharge characteristics based on linear current attenuation model;
基于电流线性衰减模型分析低能电弧放电特性
2.
The morphologies and microstructures of the cathode deposits prepared by self-sustained arc discharge between graphite rods under different conditions were investigated by means of SEM and TEM,and the relationship between the morphologies and microstructures of the carbon nanotubes and the different conditions of arc discharge was obtained.
通过实现不同条件下的电弧放电,用扫描电子显微镜(SEM)和透射电子显微镜(TEM)对阴极沉积物中碳管的形貌和微结构进行表征,得到碳管的形貌和微结构与放电条件之间的一些对应关系。
3.
The mathematical model of arc discharge for capacitive ignition was established and simulation was made.
建立了容性点燃时的电弧放电数学模型,并进行了仿真。
参考词条
补充资料：厂用电受电
厂用电受电
energizing of auxiliary power system
chongyongd一on sho一Jd一on厂用电受电(energizing of auxiliary powersystem)机组附属设备安装完毕后需通电试运行，所需厂用电源由外部供给，因此厂用电受电是调试工作开始的标志。 受电步骤新建电厂先由电力系统向变电站供电，再依次对高压起动/备用变压器、3~10kv厂用配电装置、厂用工作变压器及380V配电装置供电。扩建电厂因高压起动/备用变压器已经投人运行，故可利用它的电源对扩建的厂用配电装置等供电。 调试项目主要有:①用额定电压依次对空载线路、变电站母线、隔离开关、断瘩器、互感器、变压器及厂用配电装置等进行冲击合闸试验。有条件时.冲击合闸前应先进行递升加压试验。升压过程中注意检查各设备有无放电声及短路现象，发现问题及时处理后再进行升压。②检查三相电压应平衡，相序应正确，各段母线的相位彼此应一致。对配电装置供电时，有时会由于母线电容和与母线连接的电磁式电压互感器的电感相互作用而出现铁磁谐振，此时相电压升高，中性点明显位移。为消除谐振可在电压互感器的剩余电压绕组处并联电阻以去振。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。