1) piezothermoelastic
压电热弹性体
1.
The research on classical problems for thermoelastic、piezothermoelastic and magneto-electro-thermo-elastic structures not only can provide the analytical solution for engineering applications but also acts as the necessary benchmarks for various approximate theories and calculation methods.
本文分别以热弹性体、压电热弹性体和电磁热弹性体为研究对象,研究它们在耦合载荷作用下的全场解析解。
2.
The research on axisymmetric classical problems for thermoelastic and piezothermoelastic structures not only can provide the analytical solution for engineering applications but also acts as the necessary benchmarks for various theories of thin plates and calculation methods.
本文分别以热弹性体和压电热弹性体为研究对象,研究它们在耦合荷载下的轴对称全场解析解。
2) thermopiezoelectricity
热压电弹性
1.
The theories of thermopiezoelectricity and magnetoelasticty for microplar continua have been systemetically developed by W.
Nowacki曾建立起系统的微极热压电弹性理论和电磁热弹性理论· 戴天民对W 。
3) Piezothermoelastic
压电热弹性
1.
Two-Dimensional General Solutions and Fundamental Solutions for Orthotropic Thermoelastic Materials, Piezothermoelastic Materials and Electro-magneto-thermo-elastic Materials with Applications;
正交各向异性热弹性材料、压电热弹性材料和电磁热弹性材料的二维通解和基本解及其应用
4) magneto-electro-elastic media
压电、压磁弹性体
5) coupled piezothermoelasticity
耦合压电热弹性
6) piezothermoelastic materials
压电热弹性材料
1.
Based upon piezothermoelastic material governing equations, the homogeneous state equation for the mechanical, electric, thermal coupling problem of piezothermoelastic materials is derived by means of reforming the constitutive equations of piezothermoelastic materials as well as combining the piezothermoelastic material thermal equilibrium equations.
根据压电热弹性材料的控制方程和热传导关系,重构压电热弹性材料的本构关系,通过新本构关系并结合压电热弹性材料热平衡方程,得出压电热弹性材料机-电-热耦合问题的齐次状态方程。
补充资料：热塑弹性体热熔胶
分子式：
CAS号：
性质：热塑弹性体包括许多微区结构聚合物，如聚氨酯，SBS，SIS等。SBS是苯乙烯-丁二烯-苯乙烯嵌段，SIS是苯乙烯-异戊二烯-苯乙烯嵌段，这类嵌段共聚体是热塑性的，当冷却时又回复2相形态和弹性，特别适用于热熔压敏胶黏剂。做热熔胶时常加入工艺油降低黏度，加入2种增黏剂，一种与二烯或脂肪嵌段相混溶，而另一种增黏剂溶混并增强聚苯乙烯嵌段，这种增黏剂包括α-甲基苯乙烯聚合物和氧茚树脂。一般还添加少量抗氧剂。
CAS号：
性质：热塑弹性体包括许多微区结构聚合物，如聚氨酯，SBS，SIS等。SBS是苯乙烯-丁二烯-苯乙烯嵌段，SIS是苯乙烯-异戊二烯-苯乙烯嵌段，这类嵌段共聚体是热塑性的，当冷却时又回复2相形态和弹性，特别适用于热熔压敏胶黏剂。做热熔胶时常加入工艺油降低黏度，加入2种增黏剂，一种与二烯或脂肪嵌段相混溶，而另一种增黏剂溶混并增强聚苯乙烯嵌段，这种增黏剂包括α-甲基苯乙烯聚合物和氧茚树脂。一般还添加少量抗氧剂。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条