1) axial space
轴向空间
2) Urban-Axial-Development
城市空间轴向发展
1.
Study on the Power Mechanism of Urban-Axial-Development’s Evolution;
城市空间轴向发展演变的动力机制分析
3) axial clearance
轴向间隙
1.
Analysis the producing ways of axial clearance of bent axises on X195 diesel;
保证X195柴油机曲轴总成轴向间隙几种生产方式的讨论
2.
The method of eliminating axial clearance,logical fixing configuration and effective guard of ballscrew nut pair are all introduced in this paper.
介绍滚珠丝杆螺母副轴向间隙的消除方法、合理的安装结构和有效的防护装置。
3.
It was found that these faults were attributed to(1) the excess axial clearance of the rolls at the bearing seat,and(2) the excess bouncing resulting from the unbalanced force applied to the rubber mat of the rolls.
经分析,原因是轧辊非传动端轴承座装配的轴向间隙过大,且螺纹公差偏大,所以造成轧辊窜动严重以及原用胶垫受力不均衡,弹跳过大。
4) axial gap
轴向间隙
1.
The experimental investigation of stator clocking effect with different axial gaps shows that the variation of efficiency increases while the mass flow rate increases at fixed axial gap,but the pressure ratio changes little.
本文实验研究了在不同动、静叶间轴向间隙下静叶时序效应对某低速轴流压气机气动性能的影响。
2.
Based on parameter graph modelling axial gap can be analysed by this system during the assembling of turbodrill.
在分析涡轮钻具结构的基础上 ,论述了涡轮钻具的结构和数据的CAD表示方法 ,同时系统采用参数化图形建模方式 ,能方便地辅助分析装配过程中轴向间隙的大小 。
5) axial spacing
轴向间距
1.
Analysis of the effect of axial spacing of two successive blade rows on the measured mean flow coefficient at stall inception and on the flow range of compressor under multi-cell rotating stall operating conditions proves that the stator can suppress the flow disturbance in the compressor and strengthen the stability of the compressor.
对低速轴流压气机五个轴向间距下的压气机特性进行了试验。
2.
In order to investigate the impact of the rotor-to-stator axial spacing on the compressor stalling characteristics, experimental studies for characteristics of the low speed research compressor with different rotor/stator gaps had been carried out.
采取在静子叶片表面埋入微型压力传感器的方法,对叶尖、叶中和叶根三个截面上的动态压力进行测量,实验研究了六个轴向间距下压气机的旋转失速特性。
3.
The experimental results of a low speed single stage compressor show that stall flow coefficient decreases with the decrease of the axial spacing between rotor and stator because of the increas.
理论上论证了 ,当静子非首先失速部件时 ,其作用有利于抑制扰动的发展 ,增强压气机的气动稳定性 ;试验验证了 ,随着转静子之间轴向间距的减小 ,静子的增稳作用增强 ,压气机的失速流量减
6) Spatial Arbor
空间轴
补充资料:单轴各向异性
单轴各向异性是磁晶各向异性的最简单形式,即自发磁化的稳定方向(或易磁化方向)平行于一特殊晶轴。如六方晶系钴的自发磁化方向平行于 C轴(见晶体结构),这就表现出强的单轴各向异性。磁性材料的单轴各向异性值一般都低于其磁晶各向异性值,为103erg/cm3量级。磁性材料经磁场热处理或强的冷加工而产生的感生各向异性,都属于单轴各向异性。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条