2) soldering
[英]['sɔldə] [美]['sɑdɚ]
低温钎焊
1.
The low temperature bonding between 95%Al2O3 ceramics and 45 steel was realized through first electroless Ni-P plating on Al2O3ceramic blocks and then soldering them to steel blocks with a low melting point filler metal of 63Sn-34Pb-2Ag-1Bi alloy.
采用化学镀Ni-P膜法金属化Al2O3陶瓷,并用63Sn-34Pb-2Ag-1Bi钎料膏实现了95%Al2O3陶瓷与45钢之间的低温钎焊。
2.
Process of electroless copper plating on Al_2O_3 ceramics and its soldering at low temperature;
进行了镀铜后Al2O3陶瓷低温钎焊工艺试验,研究了不同化学镀工艺条件对接头组织及力学的影响。
3) brazing temperature
钎焊温度
1.
Electron beam brazing temperature field PID control system;
电子束钎焊温度场PID控制系统
2.
Effect of processing parameters including brazing temperature and holding time on the joint mechanical property was also discussed by optical microscope,SEM and EDS.
研究表明,钎焊温度为900℃,保温时间为5 min时,接头抗剪强度最高,达144 MPa。
3.
The effects of brazing temperature and time on the structure and property of the brazed joint between graphite and TZM alloys with Ti-based filler in vacuum were presented.
研究了钛合金真空钎焊石墨与TZM合金过程中,钎焊温度和时间对钎焊接头组织和性能的影响。
4) soldering temperature
钎焊温度
1.
The method to ensure proper soldering temperature and the principle for that is also dealt with.
指出了保证钎焊温度的方法及其原理等。
2.
The results showed that the IMC on the joint boundary indicated the difference in its formation and distribution under different soldering temperatures and times, resulting in the variation of the joint shearing strength.
结果表明:在不同的钎焊温度和钎焊时间条件下,接头界面处金属间化合物的形成及分布是不同的,并由此导致了接头抗剪强度的变化。
3.
The results show that the melting properties of the solder alloy are satisfactory,and the soldering temperature and time have much effect on the shearing-strength of the joints.
制备了急冷型SnAgCu系钎料合金,在对其进行熔化特性测定和钎焊工艺试验后,对钎焊接头的力学性能和显微组织进行了测试分析,结果表明:所制备钎料合金的熔化特性满足要求;钎焊温度和钎焊时间对接头的剪切强度有较大影响,工艺参数为275℃×4。
5) high temperature brazing
高温钎焊
1.
Joining of recrystallized SiC ceramic to itself has been realized by high temperature brazing process using Ni-51Cr (containing 51wt%Cr) as filler.
采用Ni-51Cr(含质量分数为51%Cr)焊料高温钎焊再结晶SiC陶瓷,研究了连接温度、保温时间以及焊料量等对接头三点抗弯强度的影响,并对连接界面区域的微观结构及焊料反应产物进行了SEM,EDS及XRD分析。
6) high temperature welding
高温钎焊
1.
Joining of high strength graphite has been realized by high temperature welding with Ti+Ni solder.
采用Ti基活性钎料对高强石墨进行了高温钎焊试验。
补充资料：春暮过石龟谷题温处士林园（一作送温逸人）
【诗文】：
隐几无名老，何年此陆沈。丘园自得性，婚嫁不婴心。
岁计因山薄，霞栖在谷深。设罝连草色，晒药背松阴。
触兴云生岫，随耕鸟下林。支颐笑来客，头上有朝簪。
【注释】：
【出处】：
全唐诗：卷238_41
隐几无名老，何年此陆沈。丘园自得性，婚嫁不婴心。
岁计因山薄，霞栖在谷深。设罝连草色，晒药背松阴。
触兴云生岫，随耕鸟下林。支颐笑来客，头上有朝簪。
【注释】：
【出处】：
全唐诗：卷238_41
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条