2) large-size crystal ingot
大尺寸晶锭
3) maximum grain size difference
最大晶粒尺寸差
4) grain size
晶粒尺寸
1.
Influence of wire rolling process parameters on austenite grain size of high carbon steel;
高碳钢线材轧制工艺参数对晶粒尺寸的影响
2.
Prediction of the flow behavior and grain size during forming for nickel alloy heavy forging;
镍基合金大锻件成形过程流变行为与晶粒尺寸预测
3.
Modelling for grain size and flow stress of magnesium alloy based on BP neural network;
基于BP神经网络的镁合金晶粒尺寸及流变应力模型
5) crystallite size
微晶尺寸
1.
The increase of crystallite size and notable changes of orientation factor for crystal planes during blow molding process reveale.
结果表明经过吹塑成型过程后,TPCC的熔融温度、结晶度均较TPC有所提高,DSC熔融半峰宽明显下降,微晶尺寸明显增大,同时晶面取向因子发生显著变化,表明成型过程中晶区尺寸增大,且晶体结构更均匀规整,赋予了输液瓶良好的性能。
2.
The crystallite size, degree of crystallinity( X c) and thermal properties of the [poly(cyanoarylether PCE)] at various temperatures have been studied by using WAXD and DSC.
利用广角 X射线衍射 (WAXD)方法和示差扫描量热法 (DSC)研究了不同热处理温度时聚芳醚腈 (PCE)的微晶尺寸、结晶度及热性能的变化。
3.
The resultsshowed that after the treatment of cellulose with L-NH3, the lateral order distribution,crystallinity, crystallite size and lattice form of cellulose were dramatically changed.
结果表明，液氮处理后纤维素的侧序分布、结晶度、微晶尺寸、晶格形态都发生深刻的变化。
6) crystallite size
晶粒尺寸
1.
Determination of crystallite size and strain by X-ray powder
晶粒尺寸和应变的X射线粉末衍射法测定
2.
The effects of the amount of Gd~ 3+ -doping and calcination temperature on the photocatalytic activity for photocatalytic degradation of methylene blue (MB) in aqueous solution, phase structure, crystallite size, surface texture properties of the nanopowders were investigated,and t.
研究了Gd3+掺杂量和焙烧温度对样品光催化降解亚甲基蓝的活性、相结构、晶粒尺寸和表面织构特性的影响,并结合表面光电特性和表面组成等探讨了Gd3+掺杂对纳米TiO2的光催化活性的影响机制。
3.
The effects of pHinitial value, hydrothermal temperature and hydrothermal time on the morphology, crystal phase and crystallite size of TiO2 powder were investigated.
研究了反应初始pH值、水热反应温度和水热反应时间对TiO2形貌、物相和晶粒尺寸的影响。
补充资料：工程图标准尺寸及坐标尺寸
标准标注类型，是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。
· 3.2 标准标注到坐标标注的转换
注意： 转化为坐标标注的尺寸必须是线性标注的，下列尺寸不能转化为坐标标注：
- 被显示成线性尺寸的直径
- 中心线尺寸
- 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
- 选择作为参考基准线的尺寸
- 选择基准的引出线，该点为0点
- 选择 MOD DIM TYPE > Lin to Ord .
- 选择线性尺寸：注意：必须选择具有相同基准的尺寸
========>>>>
1. 选择 DIM PARAMS > Diam Dim Type .
2.点击Ord to Lin 
3.选择尺寸即可
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条