2) armored steel
装甲钢
1.
Finite element analysis of anti-break performance and anti-shock strength of the armored steel thermit welding joint;
装甲钢板铝热焊接头抗断性和抗击强度有限元分析
2.
HAZ/WM interfacial microstructure is observed either in as-welded or as-quenched(PWHT:900 ℃×5 min or 1 100 ℃×1 min,Water-quenched)TWE312/616 high-strength armored steel weldments by means of SEM or TEM respectively.
采用SEM、TEM观察焊态和焊后热处理(900℃×5min或1100℃×1min,水淬)TWE312/616装甲钢HAZ/WM界面区及其附近的组织结构,采用NanoTest600对界面区附近的硬度分布进行测试。
3) armor steel
装甲钢
1.
The microstructure has been analyzed to the armor steel with attacks,it was discovered that the destruction of armored steel under the impact load is first produces the crack source in the crystal boundary intersection point,then connects mutually.
通过对冲击破坏装甲钢组织分析,发现纯净装甲钢在冲击载荷下破坏过程中是在晶界交汇处(三叉点)产生裂纹源,然后相互连接的结果。
2.
Four points bending low-cycle fatigue lifetime of armor steel 616 Tee joints after weld finishing has been analyzed and measures to improve the fatigue lifetime have been proposed in the paper.
本文对转炉 6 16装甲钢T型焊接接头四点弯曲低周疲劳试验结果进行了分析、研究 ,阐述了提高T型焊接接头低周疲劳寿命的有效措施。
3.
The dynamic compression properties of armor steel 603 and 675 have been systematically tested using a one-dimension Hopkinson compression bar apparatus.
利用一维Hopkinson压杆实验设备,对603、675两种装甲钢的动态压缩力学性能进行了较为系统的测试,在此基础上建立了2种装甲钢的Bodner-Partom本构方程,经程序计算与实际试验结果对比,表明本构方程能够较好地反映材料在动载荷条件下的力学行为。
4) 675 armor steel
675装甲钢
1.
Effect of cooling rate on microstructure in 675 armor steel;
冷却速度对675装甲钢显微组织的影响
2.
Transformation process and microstructure in 675 armor steel continuously cooled at a series of different rates were investigated using a high-resolution dilatometer,along with optical and transmission electron microscope.
利用差分膨胀仪、金相及透射电镜研究了675装甲钢过冷奥氏体在不同冷却速度下的相变过程及产物。
5) armor plate
装甲钢
1.
The relativity between natural and the artificial accelerated environmental test of armor plate in acid rain atmospheric environment was studied.
对某型装甲钢在酸雨大气环境下自然暴露与人工模拟加速试验的相关性进行了研究。
2.
By utilizing the numerical simulation combined with the experiment, the anti-penetration characteristics of steel fiber reinforced concrete (SFRC) targets within the A97-ceramic-plate or the armor plate are studied.
采用数值模拟与实验相结合的方法,对A97陶瓷板钢纤维混凝土靶及某种装甲钢板钢纤维混凝土靶抗动能长杆射弹的特性进行了研究。
6) 22SiMn2TiB armor plate
22SiMn2TiB装甲钢
1.
When the routine ultrasonic probes are used to detect the dissimilar welding joint of the 22SiMn2TiB armor plate, there are many noisy and false waves and which lead to the lowness of the signal-to-noise ratio attainability and sensitivity.
用常规探头对22SiMn2TiB装甲钢与TWE312异种钢焊接接头进行缺陷检测,杂波和伪缺陷波导致灵敏度、信噪比不高。
补充资料：diatomite filter-air ZX-616
分子式：
分子量：
CAS号：
密度：2.1～2.3
性状：白色或淡黄色粉末。
用途：化学性质稳定。在过滤中可获得足够的过滤与澄清速度。用于啤酒、果酒、饮料、食油、药液、饮用水等的过滤。
制备或来源：由优质硅藻土经高温助熔、煅烧而成。
备注：水分≤3%，pH7.4,渗透率2.5～6.0，堆积密度0.36～0.45，二氧化硅含量91%。
分子量：
CAS号：
密度：2.1～2.3
性状：白色或淡黄色粉末。
用途：化学性质稳定。在过滤中可获得足够的过滤与澄清速度。用于啤酒、果酒、饮料、食油、药液、饮用水等的过滤。
制备或来源：由优质硅藻土经高温助熔、煅烧而成。
备注：水分≤3%，pH7.4,渗透率2.5～6.0，堆积密度0.36～0.45，二氧化硅含量91%。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条