1) multi-layer spray co-deposition
多层喷射共沉积
2) Multi-layer Spray Deposition
多层喷射沉积
1.
Mechanism of multi-layer spray deposition of bimetal;
多层喷射沉积制备双金属板材的机理初探
2.
By the application of programmable controller in the preparation technology of multi-layer spray deposition,automatic control over scanning movement of the spray system and withdrawal movement of the preform can be executed to regulate the outline and size of deposited blanks more precisely.
在多层喷射沉积管坯与柱坯制备工艺中 ,采用可编程调节器可实现喷射系统扫描运动与坯体下降运动的自动控制 ,较精确地控制沉积坯的外形、尺寸 ,制备出了尺寸达Φ外650 /Φ内 3 60mm ,长 12 0 0mm的各种铝合金管坯与Φ30 0～ 50 0mm的铝合金柱
3.
7Si alloy tubes are prepared by multi-layer spray deposition.
采用多层喷射沉积装置与技术制备 外 6 5 0 / 内 3 6 0× 12 0 0mm的大型厚壁Al- 8。
3) multi layer spray deposition
多层喷射沉积
1.
It shows that multi layer spray deposition have many merits, for example: simple techniques, high adhesion strength etc.
采用多层喷射沉积技术制备铝 /钢双金属板 ,分析了其中对双金属板界面结合产生影响的因素。
2.
Large scale 6066Al/SiC p/Gr composite tube with size up to 650mm in outer diameter, 300 mm in inner diameter and 800 mm in length has been prepared by multi layer spray deposition and twin atomizer system, and then extruded into tube product of 350 mm in outer diameter and 250 mm in inner diameter.
采用多层喷射沉积技术与双喷嘴雾化系统制备了外径为 6 5 0mm ,内径为 30 0mm ,长为 80 0mm的大尺寸6 0 6 6Al/SiCp/Gr颗粒增强复合材料管坯 ,并成功挤压外径为 35 0mm ,内径为 2 5 0mm的管材 。
3.
A hypereutectic Al Si Cu Mg alloy is fabricated by multi layer spray deposition technology which has more advantages than the traditional spray deposition such as higher cooling rate, simple technological route and lower oxidation.
多层喷射沉积技术具有冷速快、工艺简单、氧化程度低、制备的材料组织细小且分布均匀等特点 。
4) spray deposition
喷射共沉积
1.
Spray deposition is considered to be one of the most effective technologies to produce such materials.
但国际上现有的喷射沉积技术难以制备大尺寸和特大尺寸的快速凝固坯件,为了解决大尺寸快速凝固材料坯件的制备问题,作者设计出了新型的喷射沉积装置,研究了技术原理,结合一项国家“十五”攻关项目对喷射共沉积7075/SiC_p复合材料的制备工艺、沉积坯的致密化和热处理工艺规律、材料组织性能以及复合材料的摩擦磨损性能等进行了研究。
2.
The SiC_p/2024 Al matrix composite rolling plates were prepared by spray deposition,rolling after hot extrusion.
利用喷射共沉积、热挤压、轧制工艺制备了SiC_p/2024铝基复合材料轧板,通过OM、SEM、TEM及XRD等手段研究了该复合材料轧制态和热处理态的显微组织和力学性能。
5) spray co-deposition
喷射共沉积
1.
Rolling processing of spray co-deposition 7075/SiC_p composite;
喷射共沉积7075/SiC_p复合材料薄板的轧制成形
2.
The novel device and the method to prepare 6066/SiC_p billet by spray co-deposition with scanning atomizer to and fro were presented,and compared with that of the traditional spray co-deposition equipment.
提出了雾化器往复扫描喷射共沉积制备6066/SiCp的装置和方法,并与传统的喷射共沉积装置进行了比较。
3.
SiC particulated-reinforced 7000 series metal-matrix composites were prepared by spray co-deposition with moving crucible.
采用坩埚移动式喷射共沉积技术制备了SiC颗粒增强7000系铝基复合材料，研究了经热挤压加工和固溶时效处理后复合材料的组织和性能衍变以及材料的摩擦磨损性能。
6) spray co deposition
喷射共沉积
1.
73Mg/SiC P composites produced by spray co deposition; meanwhile, the mechanical properties and wear resistance ability of the materials were given.
采用ＴＥＭ 技术分析了喷射共沉积态及挤压态Ａｌ－４。
2.
The SiCp/Al composites with 35 vol% SiCp have been made by spray co deposition.
用喷射共沉积技术制备了含３５ｖｏｌ％ＳｉＣ的ＳｉＣｐ／Ａｌ复合材料。
补充资料：多层沉积层
分子式：
CAS号：
性质：由两种或两种以上相继沉积的金属构成的沉积层。这些沉积层可以由不同特性的同一金属或不同金属构成。如为了提高镍镀层的防护性，有时采用双层镍或三层镍镀层。又如为防护-装饰目的采用的铜/镍/铬三层镀层。
CAS号：
性质：由两种或两种以上相继沉积的金属构成的沉积层。这些沉积层可以由不同特性的同一金属或不同金属构成。如为了提高镍镀层的防护性，有时采用双层镍或三层镍镀层。又如为防护-装饰目的采用的铜/镍/铬三层镀层。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条