1) Spray co-deposition
喷雾共沉积
1.
It is indicated that the high strength and high conductivity materials can be expected to be produced by spray co-deposition process by more detailed analysis of both the specificity of such process and the strenthening mechanism of high conductivity materials.
指明了发展高强度高导电率材料过程中存在的主要问题,通过对喷雾共沉积工艺过程的特殊性和高导电材料的强化机制两方面较为详尽的分析,指出采用喷雾共沉积工艺可望制备出高强度高导电率的材料。
2) spray co deposition
喷雾共沉积
1.
The typical characteritics of the spray co deposition were summerized.
概述了喷雾共沉积工艺的典型特点，指出喷雾共沉积工艺在高阻尼减振材料、耐磨减摩材料、高强度高导电材料制备方面具有广阔的前景。
2.
The paper has analysed the solidification and momemtum transportation behaviour during the process of spray co deposition technology and indicated that the nucleation mode of pore was favourable to the refining of crystal.
对喷雾共沉积工艺过程中的凝固与动量传输行为进行了分析。
3.
Three kinds of graphite particulate reinforced zinc based MMCS with 5, 10 and 15 volume fraction percent were prepared by spray co deposition.
ｇ－１Ｓｉ并采用喷雾共沉积技术制备了石墨颗粒体积分数分别为５％，１０％，１５％的锌基复合材料。
3) spray deposition
喷雾沉积
1.
Damping Properties of ZA 27 Alloy Containing Silicon Produced by Spray Deposition;
喷雾沉积含硅ZA27合金的阻尼性能
2.
ZA27 alloy doped with 4%Si (named ZA27-4%Si ) was prep ared by spray deposition technique, and then the alloy was hot extruded at 250 ℃.
用喷雾沉积快速凝固技术制备了含硅 4 %的ZA2 7合金 ,并对其进行了热挤压。
3.
This paper deals with friction and wear performance of spray deposition ZA27 alloy containing 6mg' g-1 silicon.
研究了喷雾沉积ＺＡ２７（含Ｓｉ６０ｍｇ。
4) spray atomization and co deposition
喷雾沉积法
1.
The superplasticity of aluminum matrix fabricated by spray atomization and co deposition was investigated.
喷雾沉积法制造的ＳｉＣＰ／ＬＹ１２复合材料经热压和热正挤压后，晶粒得以细化，ＳｉＣＰ分布的均匀性大大改善。
5) spray deposition
喷射共沉积
1.
Spray deposition is considered to be one of the most effective technologies to produce such materials.
但国际上现有的喷射沉积技术难以制备大尺寸和特大尺寸的快速凝固坯件,为了解决大尺寸快速凝固材料坯件的制备问题,作者设计出了新型的喷射沉积装置,研究了技术原理,结合一项国家“十五”攻关项目对喷射共沉积7075/SiC_p复合材料的制备工艺、沉积坯的致密化和热处理工艺规律、材料组织性能以及复合材料的摩擦磨损性能等进行了研究。
2.
The SiC_p/2024 Al matrix composite rolling plates were prepared by spray deposition,rolling after hot extrusion.
利用喷射共沉积、热挤压、轧制工艺制备了SiC_p/2024铝基复合材料轧板,通过OM、SEM、TEM及XRD等手段研究了该复合材料轧制态和热处理态的显微组织和力学性能。
6) spray co-deposition
喷射共沉积
1.
Rolling processing of spray co-deposition 7075/SiC_p composite;
喷射共沉积7075/SiC_p复合材料薄板的轧制成形
2.
The novel device and the method to prepare 6066/SiC_p billet by spray co-deposition with scanning atomizer to and fro were presented,and compared with that of the traditional spray co-deposition equipment.
提出了雾化器往复扫描喷射共沉积制备6066/SiCp的装置和方法,并与传统的喷射共沉积装置进行了比较。
3.
SiC particulated-reinforced 7000 series metal-matrix composites were prepared by spray co-deposition with moving crucible.
采用坩埚移动式喷射共沉积技术制备了SiC颗粒增强7000系铝基复合材料，研究了经热挤压加工和固溶时效处理后复合材料的组织和性能衍变以及材料的摩擦磨损性能。
补充资料：不共中不共变
【不共中不共变】
谓如眼等五根，唯自己第八识中最初一念，托父母遗体时变现，名不共；出胎之后，唯自己受用，复名不共。如眼识，惟依眼根而发；乃至身识，唯依身根而发，不相混杂，是为不共中不共变。
谓如眼等五根，唯自己第八识中最初一念，托父母遗体时变现，名不共；出胎之后，唯自己受用，复名不共。如眼识，惟依眼根而发；乃至身识，唯依身根而发，不相混杂，是为不共中不共变。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条