1) precise model
严密模型
2) close
严密
1.
The entry-exit inspection stations throughout the country should raise the awareness of the officers and soldiers, strengthen and enhance the organizations, so as to meet the requirement of more affinity service and more close administration and control.
确保奥运会安全、顺利、成功举办,是当前压倒一切的政治任务,全国边防检查机关广大官兵要提高思想认识,加强组织领导,加大各项工作力度,真正做到"服务更加亲切,管控更加严密",推动边检服务工作再上新台阶。
3) tightness
严密性
1.
Measures to improve the tightness of air-duct made of galvanized sheet;
镀锌板风管严密性的改进与提高措施
2.
ACC tightness is one of the key targets to examine the power plant unit,it directly influences the units of economic operation.
汽轮机真空系统严密性是考核汽轮发电机组的主要经济技术指标之一,它直接影响机组的经济运行。
3.
The influence of vacuum system tightness of 200 MW unit on the unit operation is discussed.
对于200MW机组真空系统严密性对机组运行造成的影响进行探讨,介绍真空系统查漏工作的正确思路,分析查漏过程中应注意的问题,并根据作者的实践经验介绍工作中可能存在的技术难题。
4) rigorous adjustment
严密平差
1.
The condition equations?normal equations?precision evaluation of rigorous adjustment methods with two shafts orientation and Gyro orientation jointing application have been discussed with a case studies for the feasibility and precision promotion.
分析两井定向与陀螺定向联合应用的必要性,推导两井定向与陀螺定向联合应用严密平差方法的条件方程式、法方程、求解公式及精度评定公式,并用实例验证这种方法的可行性及精度增益。
2.
The paper introduces a method of horizontal control survey of tunnel s exterior by adopting polygon closed traverse loop, assumed independent coordinate system , rigorous adjustment , adopting approximation to estimate the lateral error of tunnel and the calculation of precise kilometer and curve turn angles,thus the throughout accuracy of the tunnel was improved.
介绍了采用多边形闭合导线环、假设独立坐标系统、严密平差的方法进行隧道的洞外平面控制 ,采用近似方法估算隧道的横向贯通误差 ,以及精测里程和曲线转向角的推算 ,从而达到了提高隧道贯通精度的目
5) Tight Degree
严密度
1.
Study On The Factors That Affect The Tight Degree of Pulverous Needle Agents;
对影响粉针严密度因素的探讨
6) tight shutoff
严密切断
1.
Characteristics of the rotary valve with adjustable range,tight shutoff,more capacity,resisting cavitation etc.
分析了旋转阀在可调范围、严密切断、流通能力、抗气蚀、无外泄漏等方面的特点 ,指出了旋转阀在炼油化工装置中的应用趋势。
参考词条
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率
开始
先看下最终效果

第一步,如图所示将窗口分为四个视图

第二步,依次选择每个窗口,在分别输入各自己的视图

第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图

第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:

第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:

第六步:画出螺栓的初步形状.如图

第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算


第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集

第九步:阵列

第10步.模型就完成了

来一张利用矢量处理的图片

说明:补充资料仅用于学习参考,请勿用于其它任何用途。