1) sequential testing diagram
序贯检验图
2) sequential mesh test
序贯网图检验
1.
Bayesian sequential mesh test for success ratio;
成败型试验的Bayes序贯网图检验法
2.
This paper discussed the sample inspection problem under Rayleigh distribution, and proposed sequential mesh test.
针对瞄准发射系统中着落点位置通常服从瑞利分布的事实,研究了计量型检验问题,建立了基于瑞利分布的序贯网图检验。
3.
This paper proposed a new sampling plan, the sequential mesh test, in order to overcome the disadvantages of the widely used Sequential Probability Ratio Test (SPRT).
针对序贯概率比检验(SPRT)无法控制抽取样本量等不足之处,提出了一种改进的抽样检验方法——序贯网图检验。
3) sequential test
序贯检验
1.
,design an ameliorate sequential test(if c 1t <s,assume c 1t =c 1t ;if c 1t ≥s,assume c 1t =s):n 1 (0,c 11 ),n 2 (1,c 12 ),.
利用Wald的序贯概率比检验中接收产品时对应的批检验数 :n1 (0 ,c1 1 ) ,n2 (1 ,c1 2 ) ,… ,nk (k - 1 ,c1k) ,… ,设计出一种改进型序贯检验 (其中当c1t
2.
Aiming at this problem,a new trajectory consistence evaluation method based on probability circle and sequential test was recommended according to mathematical statistics,shooting theory and the theory of sequential test.
基于数理统计、射击理论和序贯试验理论,提出了一种基于概率圆序贯检验的弹道一致性评定新方法。
4) Bayes sequential test
Bayes序贯检验
1.
According to very small sample of the weapon system test,the Bayes sequential test method on MTBF of weapon system is researched.
针对武器系统试验鉴定中显著具有的小子样的特点,研究了武器系统平均故障间隔时间(MTBF)的Bayes序贯检验方法,推导了检验模型,平均试验数计算公式、定时和定数截尾实际风险计算公式,并给出了算例。
5) Sequential test
贯序检验法
6) sequential probability ratio test
序贯概率比检验
1.
This method uses Kalman filter to acquire the residuals of the sensor and uses sequential probability ratio test to detect the fault based on multi-residuals,which can get the least number of the residuals by dynamical calculation and has some adaptive characteristic.
这种故障检测方法采用了Kalman滤波器进行滤波来获得残差,并采用序贯概率比检验来实现多残差检测故障,针对不同的情况能动态的调整检测故障检测所需要最小的残差数目,具有自适应的某些特点,用来解决多数据检测某传感器小偏置量故障的实时性和高准确率问题。
2.
The second,which is related to sequential probability ratio test,reduces multivariate CUSUM to a univariate nomral CUSUM when the mean in the bad state(or at least the bad direction)is known.
第1种是利用 Hotelling 统计量进行累积和,形成多元累积和控制图,并讨论了它的平均游程长度(ARL);第2种是在已知偏移状态下,用序贯概率比检验法将多元累积和问题转化为一元累积和问题。
3.
Using sequential probability ratio test n 1 (0,c 11 ),n 2 (1,c 12 ),.
利用Wald的序贯概率比检验中接收产品时对应的批检验数 :n1 (0 ,c1 1 ) ,n2 (1 ,c1 2 ) ,… ,nk (k - 1 ,c1k) ,… ,设计出一种改进型序贯检验 (其中当c1t
补充资料：不合格百分率计数检验的序贯抽样方案
不合格百分率计数检验的序贯抽样方案
sequential sampling plans for inspection by attributes for percent nonconforming
加hege比ifen.o Jishu Jianvan dex叩uanC伙泪四叩fa叩’On不合格百分率计数检验的序贯抽样方案(se-quenti吐~plingp】川15 for inspection场attributesforpe二ni nonconfo丽ng)逐个地(或成组地)抽取个体，但事先并不固定它们的个数，根据事先规定的规则，直到可以做出接收或拒收批的决定为止。作为代表性的是IEC 1 123:l卯l标准。 设在n.抽试产品中出现;个不合格，且抽样方案给出:，h两数。判决规则如下:①如;n一h〕r，则接收;②如:n一h
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条