1) single-lap joint
单搭接头
1.
The stress and stiffness models of a single-lap joint are developed based on the linear elasticity theory considering the adherend shear deformations.
应力模型中的正应力和剪应力与有限元解吻合得较好,证明理论模型正确,参数研究中确定了影响胶焊单搭接头应力分布特征的关键耦合参数。
2.
Shear experiments of three types of single-lap composite joints,processed respectively by using RTM,stitched RTM and adhesively bonded techniques,are carried out to investigate the influences of process on mechanical properties of composite single-lap joint and failure mechanism is discussed from experimental observation.
在常温和湿热高温的环境下,分别进行了三种不同的成型工艺(RTM、引入缝纫的RTM和胶接)制备的单搭接头的剪切强度实验,研究了成型工艺对单搭接头的剪切强度的影响,并根据实验现象分析了单搭接头的剪切破坏机理。
3.
Shearing experiments were carried out to investigate mechanical properties of composite single-lap joints,processed by using the RTM techniques,and failure mechanism was discussed from experimental observation.
在常温环境下,进行了RTM成型工艺制备的复合材料单搭接头的剪切强度实验,记录并处理了实验数据;根据实验现象分析了单搭接头的破坏机理;建立了RTM复合材料单搭接头的三维(3D)有限元模型,模拟了搭接头的拉伸剪切破坏过程,并预测了搭接头破坏位置与破坏载荷,预测结果与实验现象吻合良好。
2) single lap joint
单搭接接头
1.
Effect of preformed angle on the shear strength of adhesively bonded single lap joints;
预偏角对单搭接接头强度的影响
2.
Numerical analysis on stress distribution in single lap joint with a metal inlay
含镶嵌块单搭接接头应力分布的数值分析
3.
The effect of elastic modulus of adhesive on the str es s distribution in aluminium alloy single lap joint was investigated using elasti c-plastic finite element method(FEM).
运用弹塑性有限元法,研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头上应力分布的影响。
3) single-lap joint
单搭接接头
1.
s: The effect of curing condition of HT1012 conductive adhesive on the shear strength of single-lap joint was investigated.
研究了固化工艺参数对由HT10 12型铜粉导电胶制备的单搭接接头剪切强度的影响。
4) single-lap joints
单搭接接头
1.
Influence of length and position of recessing on bonding strength of single-lap joints;
间隙长度与间隙位置对单搭接接头强度的影响
2.
s:The effect of the recessing length on the strength and stress distribution of adhesively bonded single-lap joints was discussed.
研究了在单搭接接头上、胶缝中预留的不同长度间隙对接头剪切强度和剪切应力分布的影响。
3.
Based on analyzing finite element model for concentrated recessing in adhesively bonded single-lap joints, a new method of instead of plane strain condition with plane stress model is used in this paper to investigate the shear stress distribution in continuous or intermittent recessing adhesive layer.
在分析现有的单搭接接头胶层中有集中间隙的有限元模型的基础上,提出了用平面应力随厚度变化的模型取代平面应变模型思路,对比了连续胶层与胶层中有3个断续间隙时搭接部位上剪切应力分布情况。
5) adhesively bonded single lap joint
单搭接粘接接头
1.
A design conception on probabilistic statistics was introduced into adhesively bonded single lap joint,and finite element method was applied to analyze the factors which have important influences on the mechanical property of adhesive joint.
将概率统计的设计观念引入单搭接粘接接头,通过有限元分析方法分析了对粘接接头力学性能影响较大的因素,并在抽样100次的情况下,分析了单搭接粘接接头失效的概率。
6) single-lap joint
单搭接胶接接头
1.
Influences of adherent thickness,temperature and velocity on strength of adhesively-bonded single-lap joints
板厚、温度和速度对单搭接胶接接头强度的影响
补充资料：装箱单、重量单、尺码单
装箱单、重量单、尺码单
[装箱单、皿t单、尺码单1装箱单(Pack-ing Ust)是说明货物包装情况的单据，包括包装材料、包装方式，以及详细的包装内容，如花色、规格搭配等。进口地海关主要依据装箱单对某一特定内容的包装内容进行检查，也是进口商核对货物的依据。装箱单的内容有:单据名称、卖方名称、唆头、件数、规格、数量、毛净重、签字等。 重量单(Weight ust)是由卖方或第三者提供的，表明货物重量的单据。一般包括皮、毛、净重。它必须和其他单据上所表示的货物重量一致。 尺码单就不详细介绍了。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条