1)  laser process
激光落料
2)  laser
激光
1.
Analysis model and experimental research of dilution in laser induction hybrid cladding;
激光感应复合熔覆的稀释率分析模型及实验研究
2.
The Reconfigurable Multifunction Laser Processing System Based on the Optimal Slice Process;
基于最优切片工艺的可重构多功能激光加工系统
3.
Study of laser transmission effect in dye-cholesteric liquid crystals;
激光在手性染料液晶中的传输效应研究
3)  lasers
激光
1.
Comparison of histologic,biochemical and mechanical properties of murine skin treated with the long-pulse and Q-switched 1 064-nm Nd:YAG lasers;
长脉宽与Q开关1064nm Nd:YAG激光对皮肤作用的比较
2.
Combined Application of Argon and Nd: YAG Lasers in Treatment of Primary Angle-Closure Glaueoma;
氩激光联合Nd:YAG激光治疗原发性闭角型青光眼
3.
Unification Single Mode Equation of Class-B Lasers with Homogeneous Broad Line;
B 类均匀加宽激光器单模方程的统一性
4)  laser beam
激光
1.
The results show that:①the transient field become quasi-steady state after the laser beam scans 2 pots ②the peak temperature and the temperature difference of upper-lower surface calculated by 2D FEM are close with that calculated by 3D FEM ③good agreement is obtained between experimental and analytical result
用小步距间歇跳跃式移动光源模拟激光束的连续扫描，采用简化模型，对板料激光成形时的三维瞬态温度场进行了有限元分析。
2.
The polarization of the laser beam output from the PHC-1 500 laser unit was experimentally verified.
试验验证了PHC-1500型CO2激光器输出激光经传输光路转换后的偏振化方向。
5)  He-Ne laser
激光
1.
Study of information transfer mechanism on interaction between He-Ne laser and bio-tissue;
He-Ne激光与生物组织相互作用的信息传递机理研究
2.
Nursing and clinical observation of the patients with herpes zoster treated by He-Ne Laser;
氦-氖激光局部照射对带状疱疹的疗效观察及护理
3.
The objective of this study was to determine the regulation effects of He-Ne laser on protein metabolism,photosynthesis of Isatis indigotica seedlings exposed to enhanced ultraviolet-B(UV-B) lesions.
以菘蓝(Isatis indigotica Fort)幼苗为实验材料,比较研究了He-Ne激光对增强UV-B(辐射强度:10。
6)  laser-assisted
激光
1.
Comparison of laser in situ keratomileusis and laser-assisted subepithelial keratectomy for myopia more than-10.00 diopters;
两种准分子激光手术治疗超高度近视的对比研究
2.
Stromal cells change after epipolis laser in situ keratomileusis and laser-assisted subepithelial keratectomy in rabbits;
微型角膜刀法与乙醇浸润法准分子激光角膜上皮瓣下磨镶术对角膜基质细胞影响的实验研究
3.
Recovery of corneal sensitivity after laser in situ keratomileusis and laser-assisted subepithelial keratectomy;
准分子激光原位角膜磨镶术与准分子激光角膜上皮瓣下磨镶术后角膜知觉恢复的研究
参考词条
补充资料：封盖落料-拉伸-切边-成形复合模

兰州电机有限责任公司(甘肃兰州 790050) 杨思明
[摘要]分析了封盖零件的成形工艺特点，介绍了此类零件复合冲压模的结构设计。
关键词 封盖 复合模 落料 拉伸

1 零件分析
     图1所示为空气滤清器的封盖，生产批量大，材料为08F，料厚0.35mm，外圆直径个80mm，拉伸高度7mm，成形后口部要求无飞边。该零件是一种典型浅盖零件，该封盖原加工工艺为落料--拉伸--压延，造成口部拉伸后有飞边，需人工清除，费力费时。
2 冲压工艺分析








    经以上计算，可一次拉伸成形，凸凹模环形壁厚强度完全可以满足要求，采用一次成形工艺为：落料--拉伸--切边--成形。
3 模具结构设计与设计要点
3.1 模具结构及其工作过程
    复合棋结构如图3所示。将条料送至凹摸15上，凸凹模12下行，卸料板13压紧条料，凸凹模12与凹模15进行落料，凸凹模12继续下行，落下的圆坏料与已有压边力的压料圈5接触，拉伸凸模6与凸凹模12进行拉伸成形，凸凹模12继续下行，凸模4外圆与凸凹模12内切边模进行切边。凸凹模12再下行，拉伸凸模6与打料板7端面接触，进行压延成形。凸凹模12上行，打料板7在冲床作用下打下成品一次成形结束。

1弹簧 2顶杆 3下模座 4凸模 5压料圈 6拉伸凸模 7打料板 8卸料杆 9上模柄 10打件杆 11上模固定板 12凸凹模 13卸料板 14固定螺栓 15凹模 16下模固定板
3.2 设计要点
    (1)落料凹模15内孔D尺寸计算时取最小值，在拉伸过程中试模修配拉伸凸模6圆角半径来确定切飞边量。
    (2)拉伸凸模6与凸模4需设计成二个单独体，便于凸模4刃口刃磨，凸模4中心孔设计成螺纹孔便于起模。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。