1) force demoulding
强力脱模
2) forced demoulding
强行脱模
1.
Taking advantage of the flexible property of PE material, forced demoulding was conducted from both up and down and the core_pulling system was in the fixed half.
详细介绍了汽车后视镜框零件的特点 ,利用PE材料质软易变形的特性 ,上下强行脱模 ,定模抽芯 ,并阐述了模具设计的特点及工作过程。
3) forced demoulding
强制脱模
1.
If the lateral uplift has enough distortion space, it could be forced demoulding.
给侧向凸起留出足够的变形空间,可强制脱模。
2.
And the mechanisms of forced demoulding, two_time ejection and delayed ejection by a sliding core used in the injection mould were introduced.
分析了沐浴露瓶盖的工艺特点 ,介绍了瓶盖注射模的结构及工作过程 ,并介绍了注射模设计中采用的强制脱模、二次顶出、滑动型芯延时顶出机构等。
3.
The structure characteristics and working process of the mechanisms for 3_time ejection, forced demoulding, delayed kicking out the sliding core adopted in the design of the injection mould for the lid of the lotion bottle were introduced.
介绍了洗面奶瓶盖注射模设计中所采用的3次顶出、强制脱模、滑动型芯延时顶出等机构的结构特点及工作过
4) forcerd stripper mechanism
强调脱模
5) early compressive strength
脱模强度
1.
When the steamcuring process of type Ⅲ prestressed concrete sleepers was adopted,and the early compressive strength was regarded as a evaluable agents,some factors influening early compressive strength of steamcuring concrete with ultrafine fly ash were studied.
采用我国铁路Ⅲ型预应力混凝土轨枕蒸养制度,以蒸养混凝土抗压强度(尤其是脱模强度)作为评价指标,试验研究了化学激发剂种类和掺量、超细粉煤灰掺量和细度、硅灰掺量和磨细矿渣掺量等因素对蒸养超细粉煤灰混凝土强度的影响规律。
6) forced demolding
强制脱模
1.
The combined application of two-stage ejection and forced demolding in injection mold
注塑模中二次顶出、强制脱模的联合应用
补充资料：二步脱模
分子式：
CAS号：
性质：又称二次顶出。由于塑件的特殊形状或生产自动化的要求，在一次脱模动作完成后，塑件仍然难于从型腔中取出或不能自动脱落，此时就必须再增加一次脱模动作才能使塑件脱落。有时为避免一次脱模塑件受力过大，也采用二次脱模，如薄壁深腔塑件或形状复杂的制品，如一次顶出易使塑件破裂或变形，而采用二次脱模，以分散脱模力，保证制品质量。
CAS号：
性质：又称二次顶出。由于塑件的特殊形状或生产自动化的要求，在一次脱模动作完成后，塑件仍然难于从型腔中取出或不能自动脱落，此时就必须再增加一次脱模动作才能使塑件脱落。有时为避免一次脱模塑件受力过大，也采用二次脱模，如薄壁深腔塑件或形状复杂的制品，如一次顶出易使塑件破裂或变形，而采用二次脱模，以分散脱模力，保证制品质量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条